Casting wax and a solus cast ring on top of it with prestige gold( wax investment) with normal burn out ( high temp was 740) and six hours simple uv curing.
Surface is not as good as casting with resin investment but its acceptable.
Search found 39 matches
- Thu Oct 19, 2017 2:29 pm
- Forum: Casting
- Topic: SolusCast: Success Print and Cast
- Replies: 12
- Views: 24680
Re: Monogram
mongerdesigns wrote:Hmm. Are you sure, Rik? We use them as is and it works great. Are you setting the projector on ECO mode?
Yes. I reduce my new 1186 projector exposure time to 3 seconds From 4.5 in 41 microns and base to 20!!!
- Sat Sep 30, 2017 3:28 pm
- Forum: Casting
- Topic: Casting SolusCast
- Replies: 202
- Views: 307279
Re: Casting SolusCast
MAN. you have to stay objective. I d'ont think a minute the bad casting results some people are encountering is due to Plasticast or Prestige Optima™ Investment. They have to step up and get a professional grade LED curing unit. some high definition resins are a pain to cure with a nail box. there ...
- Fri Sep 29, 2017 8:51 pm
- Forum: Casting
- Topic: Casting SolusCast
- Replies: 202
- Views: 307279
Re: Casting SolusCast
Which one? Topacast, Schultheiss, Galloni, Yasui? Non of them. An Iranian VPC machine name HADAF. Hi M.A.N.; Those look like the best casting yet. What is your max temp. and how long do you leave it there? Thanks. My max temp is 800 c. And stay 3 hours. I mention again change your investment. very ...
- Fri Sep 29, 2017 7:13 am
- Forum: Casting
- Topic: Casting SolusCast
- Replies: 202
- Views: 307279
Re: Casting SolusCast
A.Joa1 wrote:Hey M.A.N
very nice!!!
Are you vacuum casting? VPC?
Thanks. Yes VPC.
- Thu Sep 28, 2017 10:32 am
- Forum: Casting
- Topic: Casting SolusCast
- Replies: 202
- Views: 307279
Re: Casting SolusCast
Hi
Six hour simple uv cure with six 8 watt uv lights
38:100 G3D SYNERGY investment
3 hour sit time
12 hours burnout cycle
Casting
I have a small bottle of soluscast.
I'm going to try to cast a full sc tree soon.
Most of your problems is from your investment.Change your investment if you can.
Six hour simple uv cure with six 8 watt uv lights
38:100 G3D SYNERGY investment
3 hour sit time
12 hours burnout cycle
Casting
I have a small bottle of soluscast.
I'm going to try to cast a full sc tree soon.
Most of your problems is from your investment.Change your investment if you can.
- Sun Sep 24, 2017 4:34 am
- Forum: Casting
- Topic: SolusCast: Success Print and Cast
- Replies: 12
- Views: 24680
Re: SolusCast: Success Print and Cast
[/quote] I use an electric kiln. It can reach 850 c degrees. Do you have additional air holes or vents in your kiln to improve combustion? What is your ramp rate when moving between the temperature stages? I see. Do you know if you see any debris in the machine after you do that? That is a very inte...
- Sun Sep 24, 2017 1:56 am
- Forum: Casting
- Topic: SolusCast: Success Print and Cast
- Replies: 12
- Views: 24680
Re: SolusCast: Success Print and Cast
What type of kiln/oven/furnace are you using to burn out the prints? You mention that vacuuming out at 0.4 bar as being important. How did you go about doing this? With a vacuum chamber or an actual vacuum? How did you measure the pressure? I use an electric kiln. It can reach 850 c degrees. I vacu...
- Sat Sep 23, 2017 3:00 pm
- Forum: Casting
- Topic: SolusCast: Success Print and Cast
- Replies: 12
- Views: 24680
Re: SolusCast: Success Print and Cast
I use vacuum casting.
Its a british investment. It shwbe available in us.
I used to use prestige optima for my b9 models. I think that should work too. But synergy investment quality is much better.
Its a british investment. It shwbe available in us.
I used to use prestige optima for my b9 models. I think that should work too. But synergy investment quality is much better.
- Sat Sep 23, 2017 11:55 am
- Forum: Casting
- Topic: SolusCast: Success Print and Cast
- Replies: 12
- Views: 24680
Re: SolusCast: Success Print and Cast
Thank you