Search found 13 matches

by englishcadmaster
Tue Feb 26, 2019 9:45 pm
Forum: General
Topic: Back using my solus after more than a year
Replies: 5
Views: 922

Back using my solus after more than a year

I did upgrade the tilt motor while ago , I got the aluminum bath and the contour software. I was using the proto resin and have just done so again results are good for mold making. I need to now use a castable resin......... the ccw resin looks to have good results so need to order that but I am the...
by englishcadmaster
Sat Jul 02, 2016 6:52 am
Forum: Help and Troubleshooting
Topic: any ideas what causing this please?
Replies: 8
Views: 2877

Re: any ideas what causing this please?

okay got another build on now and wait and see. guess whats strange is that upto 4mm tall all seems well then half the build starts the fail. This is on stuff thats printed before and also the test sample ring of solus. i did wonder if the projector was doing something strange perhaps after a not pe...
by englishcadmaster
Fri Jul 01, 2016 10:19 pm
Forum: Help and Troubleshooting
Topic: any ideas what causing this please?
Replies: 8
Views: 2877

Re: any ideas what causing this please?

i did just check the build plate calibration thing with the 0.07mm paper......

I could when homed get a 0.18mm piece of paper in the gap and move it around.

now done the thin paper and tightend the build plat according to that now.

bed now but will try again with printing soon!
by englishcadmaster
Fri Jul 01, 2016 9:32 pm
Forum: Help and Troubleshooting
Topic: any ideas what causing this please?
Replies: 8
Views: 2877

Re: any ideas what causing this please?

okay will try saving and opening again in cw film wise its new as just put one on due to the other one failing in the same manner. i think I ve done it correctly but something seems certainly wrong. I had quite a few good builds but were slightly rounded on the edges..... its the in focus projector ...
by englishcadmaster
Fri Jul 01, 2016 8:36 pm
Forum: Help and Troubleshooting
Topic: any ideas what causing this please?
Replies: 8
Views: 2877

Re: any ideas what causing this please?

had a look without a vat on and the tilt seems to be tilting though never looked at it before so not really any idea how much it should move... guessing about 4mm or something at one end? not sure what you mean by pre-slicing.... i press slice and wait and it comes up with a time then I press start ...
by englishcadmaster
Fri Jul 01, 2016 3:56 pm
Forum: Help and Troubleshooting
Topic: any ideas what causing this please?
Replies: 8
Views: 2877

any ideas what causing this please?

keep getting this occurring..... first 4.5mm great then after a good start this.

it happens on previously built models that were fine I think its not the cad model.

anyone seen this before please?

had two days of this an finally going to crack soon!

thanks,

r
by englishcadmaster
Fri Jun 10, 2016 8:19 am
Forum: General
Topic: machine profile for emerald resin
Replies: 3
Views: 1430

Re: machine profile for emerald resin

hiya... unless I am missing something the numbers for the slicing profile is nt shown in that thread? The CW software from my distributor doen'st have any resin profiles in there at all..... he is away and out of the country at the moment and texted to say he thinks might be 4850 exposure and drop t...
by englishcadmaster
Thu Jun 09, 2016 6:11 pm
Forum: General
Topic: machine profile for emerald resin
Replies: 3
Views: 1430

machine profile for emerald resin

hiya...... my software isnt set up for using emerald resin I need to generate it as a profile.....

can anyone help me with the settings please?

thanks,

r
by englishcadmaster
Wed Jun 08, 2016 9:30 pm
Forum: General
Topic: first job...........
Replies: 13
Views: 5877

Re: first job...........

now getting a cube printed in resin of 20.6mm by 20.07mm by 19.98mm tall so hey seems this part is for now cracked..... I used aspect ratio so thank you all for helping. the edges are nt so crisp guess has a 0.2mm radius or something not sharp...be good to get them crisper? is that an anti alias thi...
by englishcadmaster
Tue Jun 07, 2016 6:33 pm
Forum: General
Topic: first job...........
Replies: 13
Views: 5877

Re: first job...........

hiya, mark was kind enough to hook up and sort stuff out for me. so I ve now got builds working! not perfect though as the rings are coming out oval for some reason? meaning they... are wider as they should be diameter of 16.4mm not 17.5mm...... just curing them now. internal ring size is as per pic...