Search found 29 matches

by Argyle
Sun May 06, 2018 5:20 pm
Forum: General
Topic: Can't print without lines on model
Replies: 8
Views: 5658

Re: Can't print without lines on model

It is frustrating. Its been two weeks for the OP... I've been unable to rid myself of the lines for two years.
by Argyle
Thu Apr 26, 2018 5:21 am
Forum: Software
Topic: Contour Feature Requests
Replies: 18
Views: 15314

Re: Contour Feature Requests

How about a feature to assist in the creation of resin profiles. Something where the user sets a range and the software prints a single model with varied exposure times. The printed model could then be used as a reference for several exposure times. One way this could work would be to have a stepped...
by Argyle
Fri Sep 08, 2017 2:20 pm
Forum: Resins
Topic: 385nm vs. 405nm wavelength
Replies: 3
Views: 4038

Re: 385nm vs. 405nm wavelength

Do you have a link to that BYU article?
by Argyle
Fri Aug 05, 2016 12:11 am
Forum: Help and Troubleshooting
Topic: Too many fails
Replies: 56
Views: 28364

Re: Too many fails

I recently began setting up for 42xy but while i was calibrating the build area I noticed the grid was not completely on the quartz. As I looked to see why i noticed the quartz was shifted to the left. I was wondering if this would affect my printing quality or cause print failures? Also would like...
by Argyle
Tue Aug 02, 2016 11:08 pm
Forum: Gallery
Topic: Print & Casting
Replies: 8
Views: 6104

Re: Print & Casting

The Castings
by Argyle
Sun Jul 31, 2016 9:28 pm
Forum: Help and Troubleshooting
Topic: Too many fails
Replies: 56
Views: 28364

Re: Too many fails

In the past thin vertical prints with a lot of flat surface area have been the most difficult to grow. So far so good using this method.
by Argyle
Sun Jul 31, 2016 2:15 pm
Forum: Gallery
Topic: Print & Casting
Replies: 8
Views: 6104

Re: Print & Casting

After more than a year of trial & error straying from the beaten path is giving me results I can count on! Prints are finally overtaking machining as the best method for creating my originals. :D
by Argyle
Tue Jul 26, 2016 8:11 pm
Forum: Help and Troubleshooting
Topic: [SOLVED] Print failure
Replies: 8
Views: 4225

Re: Print failure

I assume dynamic range is at full RGB in your video card settings? If not, change it. Also try lowering the bottom exposure. I found the bottom exposure in the resin profile was much higher than what I needed.
by Argyle
Tue Jul 26, 2016 4:20 pm
Forum: Help and Troubleshooting
Topic: Too many fails
Replies: 56
Views: 28364

Re: Too many fails

Thank you, I appreciate the response. I will try your method and see how it works, will post the results soon but i dont have anymore extra film. :D No problem. If what you're doing now is working I'd stick to it. There are a lot of other people on this forum getting great results using the standar...
by Argyle
Tue Jul 26, 2016 3:45 pm
Forum: Help and Troubleshooting
Topic: Too many fails
Replies: 56
Views: 28364

Re: Too many fails

Wow, nice print. You did it without the thumb screws? interesting, did the vat not move during the print? What method did you use to install the new film in the vat? Currently we have a vat that prints well and we didn't stretch the film but i am still not clear on how to install the film. Thank yo...