Search found 10 matches
- Mon Jan 29, 2018 10:39 pm
- Forum: Help and Troubleshooting
- Topic: machine making weird noises
- Replies: 8
- Views: 14962
Re: machine making weird noises
so the problem is not the the tilt table its the plate when its goes up and down, sometime it blocks and decides not to go down and u hear the motor triying to run but blocked. i run it up and down until the noise stops, so im guessing its the anti backlash nut is seizing, but the screw has been lub...
- Sat Dec 16, 2017 6:58 pm
- Forum: Help and Troubleshooting
- Topic: machine making weird noises
- Replies: 8
- Views: 14962
Re: machine making weird noises
yea the noise goes and comes back, but now its almost like it permanently there, i grease the screw every 2 weeks, but now its almost like the machine screams when it goes up and stops, and when it come down and stops. so up stop "noise", down stop " noise, its still printing but make...
- Fri Oct 27, 2017 5:39 pm
- Forum: Help and Troubleshooting
- Topic: MY QUARTS IS STUCK AT AN ANGLE AND WONT GO BACK UP
- Replies: 4
- Views: 7687
Re: MY QUARTS IS STUCK AT AN ANGLE AND WONT GO BACK UP
its all good i opened it up, the screw that brings it up had gone down to low
- Mon Oct 23, 2017 5:40 pm
- Forum: Help and Troubleshooting
- Topic: MY QUARTS IS STUCK AT AN ANGLE AND WONT GO BACK UP
- Replies: 4
- Views: 7687
MY QUARTS IS STUCK AT AN ANGLE AND WONT GO BACK UP
HI QUARTS IS STUCK AT AN ANGLE AND WONT GO BACK UP, WHAT DO I DO?
- Wed Sep 27, 2017 4:46 pm
- Forum: Help and Troubleshooting
- Topic: machine making weird noises
- Replies: 8
- Views: 14962
machine making weird noises
My solus 3d printiner si making a scratchy squeeling noise when the plate goes up and down, never had this issue before it just started this morning, what can it be from? also i see the two pillars at the back tilt when plate goes up and down. plz let me know, this kinda freaked me out thx Manuel Ta...
- Tue Apr 11, 2017 1:58 pm
- Forum: Help and Troubleshooting
- Topic: keep getting failed prints
- Replies: 4
- Views: 7435
Re: keep getting failed prints
[img]
is this it?
[/img]is this it?
- Mon Apr 10, 2017 10:07 pm
- Forum: Help and Troubleshooting
- Topic: keep getting failed prints
- Replies: 4
- Views: 7435
keep getting failed prints
[[img]
hey i keep getting the failed print every time i start the machine. but i dont get any fails when i run it with no resin vat and build plate. what can it be?
thx
Manuel
[/img]hey i keep getting the failed print every time i start the machine. but i dont get any fails when i run it with no resin vat and build plate. what can it be?
thx
Manuel
- Mon Mar 20, 2017 2:01 pm
- Forum: Help and Troubleshooting
- Topic: warped at the top
- Replies: 7
- Views: 11078
Re: warped at the top
its not only with this model it happens 80% of the time. i also pass them trough majics and repair all the file before i print anything. but if i were to put this same model horizontally i wont have that warping at the the top, it only warps where the sides of the ring connect
- Fri Mar 17, 2017 9:04 pm
- Forum: Help and Troubleshooting
- Topic: warped at the top
- Replies: 7
- Views: 11078
- Fri Mar 17, 2017 9:03 pm
- Forum: Help and Troubleshooting
- Topic: warped at the top
- Replies: 7
- Views: 11078
warped at the top
hi my names manuel recently got a solus, and my rings come out warped at the top where the finger goes through. cant figure out how to fix this problem