Search found 33 matches

by Mikkopee
Thu Oct 31, 2019 2:26 pm
Forum: Help and Troubleshooting
Topic: Calibration help
Replies: 3
Views: 212

Re: Calibration help

Have you fully calibrated the printer with a 10mm cube and used the "Scale Adjustment" feature to correct any inaccuracies? Yes, but when sidecubes are OK, middle cubes are too big and vice versa. And Y-axis is no problem and scale adjustment works fine but X-axis is problem since middle ...
by Mikkopee
Thu Oct 31, 2019 9:55 am
Forum: Help and Troubleshooting
Topic: Calibration help
Replies: 3
Views: 212

Calibration help

How do I calibrate this?

All cubes are 8x10mm

Y-axis I can fix, but X -axis is problem.. its fine in the middle but both sides are too small. How do I fix this?

Projected grid is fine and straight lines.
And measuments are 80x45mm like it should be.
by Mikkopee
Fri Oct 04, 2019 11:26 am
Forum: General
Topic: New Solus
Replies: 19
Views: 3534

Re: New Solus

mongerdesigns wrote:
rsaldivar wrote:I would like to know more about any changes to the film , how was this improved ?


The film goes on tight like a drum and is tightened in place. No tension to worry about.

Manual like old or is it automated?
by Mikkopee
Wed Mar 20, 2019 2:16 pm
Forum: Help and Troubleshooting
Topic: Printing and supports
Replies: 10
Views: 2239

Re: Printing and supports

What resin are you using?
by Mikkopee
Thu Mar 07, 2019 2:49 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 13416

Re: ResinWorks EasyCastHD castable resin

Prints nice, tomorrow first cast. Hope casts well.
by Mikkopee
Thu Feb 21, 2019 6:11 pm
Forum: Resins
Topic: ResinWorks EasyCastHD castable resin
Replies: 71
Views: 13416

Re: ResinWorks EasyCastHD castable resin

Not sticky at all. It's a really good resin. I suggest printing at 42xy build area with it for best results. Haven't had a single bad print or bad casting. It's miles better than the emerald and easier to post cure. Just cure in water for 30min - 1 hour under UV. Or for better results in glycerin o...
by Mikkopee
Fri Feb 01, 2019 2:20 pm
Forum: Help and Troubleshooting
Topic: Bending in prints
Replies: 3
Views: 1009

Re: Bending in prints

Correct you grid.
grid.jpg
by Mikkopee
Thu Jan 24, 2019 3:48 pm
Forum: Gallery
Topic: Ben's Prints
Replies: 116
Views: 52509

Re: Ben's Prints

Cool! What is you cure and casting/burnout practice?
by Mikkopee
Wed Jan 23, 2019 6:06 pm
Forum: Resins
Topic: SolusWax Tips and Tricks
Replies: 21
Views: 7698

Re: SolusWax Tips and Tricks

The resin is really thick and goopy is that normal? The Fun to Do resin I got also, is much more "watery". I have tried alot! Longest exposures I have tried where 30Z on 38sec and 5 sec for normal layers. No its not normal. Its bad. Contact you reseller to replace you SolusWax. I had that...
by Mikkopee
Wed Jan 23, 2019 4:02 pm
Forum: Resins
Topic: SolusWax Tips and Tricks
Replies: 21
Views: 7698

Re: SolusWax Tips and Tricks

How can I tell If my Soluswax resin is still good? It wont print not even on the maximum exposure times. Other resin works great. Other settings I have checked and are good. I had this same problem. I thought it was lamp, but its SW that it doesnt work. http://reify-3d.com/forum/viewtopic.php?f=3&a...