Search found 28 matches
- Fri Aug 03, 2018 3:26 pm
- Forum: Help and Troubleshooting
- Topic: Failing quality without changing anything
- Replies: 46
- Views: 63671
Re: Failing quality without changing anything
I notice your printer / vat are not very clean. If even a little amount of resin gets on the optical surfaces (quartz, front window, mirror, lenses, bottom of the film) it can block a lot of light. They would need to be cleaned multiple times using microfiber cloth and alcohol or zeiss optical wipe...
- Fri Aug 03, 2018 5:39 am
- Forum: Help and Troubleshooting
- Topic: Failing quality without changing anything
- Replies: 46
- Views: 63671
Re: Failing quality without changing anything
artcad wrote:Hi Margo,maybe you must calibrate build plate.
I did yesterday, no improvements
- Fri Aug 03, 2018 5:38 am
- Forum: Help and Troubleshooting
- Topic: Failing quality without changing anything
- Replies: 46
- Views: 63671
Re: Failing quality without changing anything
mongerdesigns wrote:Use thicker support tips. 0.4 and up. On fine details can use 0.3.
That's how I do it, yes, 0.4-0.6 on thick parts, 0.3 on the rest
- Wed Aug 01, 2018 3:58 pm
- Forum: Help and Troubleshooting
- Topic: Failing quality without changing anything
- Replies: 46
- Views: 63671
Re: Failing quality without changing anything
Sure, here it is
- Wed Aug 01, 2018 1:08 pm
- Forum: Help and Troubleshooting
- Topic: Failing quality without changing anything
- Replies: 46
- Views: 63671
Failing quality without changing anything
Hey, maybe anybody knows what can be the cause here: I've got my printer and it worked beautifully for 2 weeks, everything got printed without failing like magic. Then magic started fading away. Without changing anything, on the same saved scene, I now got not 10 out of 10 models, but first 8 out of...
- Sat Jun 09, 2018 10:14 am
- Forum: Help and Troubleshooting
- Topic: Prints fail after printing supports
- Replies: 4
- Views: 8145
Prints fail after printing supports
Hello,
Did anyone else have this problem? Prints fail after completing supports, didn't have a single good one. Resin well mixed, film is clean, supports are enough, exposure is increased from 3.7 to 3.9, it just doesn't print further and cures it on the film. Need help
Did anyone else have this problem? Prints fail after completing supports, didn't have a single good one. Resin well mixed, film is clean, supports are enough, exposure is increased from 3.7 to 3.9, it just doesn't print further and cures it on the film. Need help
- Mon Jun 04, 2018 5:32 am
- Forum: Help and Troubleshooting
- Topic: New printer - doesn't do Homing
- Replies: 2
- Views: 5773
Re: New printer - doesn't do Homing
reify wrote:Hi,
Did you download and install the arduino software? It has the drivers you need to run the printer.
Where are you located?
Hello,
yes I have, and I'm in Amsterdam.
- Sun Jun 03, 2018 8:39 pm
- Forum: Help and Troubleshooting
- Topic: New printer - doesn't do Homing
- Replies: 2
- Views: 5773
New printer - doesn't do Homing
Hi all, so I've got my new printer, assembled, set up and calibrated it, opened a calibration box model in Contour - and voila, the printer doesn't start homing. Unplugged USB (COM6 port if it's important), turned off printer, then put it back - again nothing. Contour SW sees it on COM6, but no Homi...