Search found 94 matches
- Thu Sep 01, 2016 10:48 am
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
Jesus images
- Thu Sep 01, 2016 10:47 am
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
hello, can anyone tell me as attached for exposure setting as i try 1 ring print different setting i don''t see much difference attached screen shot. did Jesus small 20mm size at 5 layer exposure time & Initial layer exposure 28 and bit bigger 4.4 & 29 check results. possbile to make more sh...
- Tue Aug 23, 2016 5:26 am
- Forum: Casting
- Topic: Airflow in burnout
- Replies: 17
- Views: 29005
Re: Airflow in burnout
@ Jewelermdt you will see B9 burnout cycle below link http://reify-3d.com/forum/viewtopic.php?f=9&t=32&p=3454#p3454 check an attached as never did casting will be first time for normal wax & castable wax will do. any other advice plz tell me i.m learning. why oven manufacturer say like t...
- Mon Aug 22, 2016 7:08 pm
- Forum: Casting
- Topic: Airflow in burnout
- Replies: 17
- Views: 29005
Re: Airflow in burnout
My oven gets air flow from a vent on top and with a small chip in the front of door panel. I have put my flasks down and when casting the cherry I did vacuum the flask. The green burns out much cleaner. No ash to worry about. I do regular wax and green resin burn out at the same time with same burn...
- Mon Aug 22, 2016 3:26 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
forgot to upload image for cure I left it in the sun, after i cureing it became harder and then i cut support, sandpaper it was feeling it's hard....i have not yet start casting yet.
- Fri Aug 19, 2016 3:35 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
setting screen short.
I''m still learning
THANK YOU VERY MUCH MARK!!!
I''m still learning
THANK YOU VERY MUCH MARK!!!
- Fri Aug 19, 2016 3:33 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
as advice by Mark i managed successful. important abt support how to set....and changed some parameter done 20 micron. attached images
- Thu Aug 18, 2016 12:14 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
1. When did Ganesha (my first time on 25xy) it was super cool no problem. i did abt 4 time now @ 80x45 not coming nice some area gets very thin and some part not growing. 2. pendant i think its bçoz of support? 3 layers are easy to notice....i removed resin from film which part did not grow but grow...
- Sun Aug 14, 2016 6:27 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
why can't we use Form-lab(preform) for auto support as they make better then B9 I personally feel.
I save as supported but unable to open in SC it don't show.
I save as supported but unable to open in SC it don't show.
- Thu Aug 11, 2016 6:55 pm
- Forum: General
- Topic: Film marking and build support problem
- Replies: 25
- Views: 36011
Re: Film marking and build support problem
same file seems came out ok attached images...will clean with soap & water in ultrasonic and 3 mins microwave 10 mins cool down 3 times......why it don't get harder like yr Solus samples!!!
it's means main power supply MARK said it's correct...
very very slightly design marks on film..
it's means main power supply MARK said it's correct...
very very slightly design marks on film..