Curing Unit
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
LED is King when it comes to big pieces curing. http://www.ebay.com/itm/QUANS-110V-20W- ... 46587158cf . It got the same LED's as the B9c curing unit or the envisiontec box.
Re: Curing Unit
Jewelermdt wrote:get the B9 cure box. 10 min your done
I got the B9 curing box the small one but im afraid that it doesn't cure well, infect after i always put them in my other home made curing box. What do you think, curing it with the B9 curing box is the enough so when i cast i dont get problems ?
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Curing Unit
If you have the B9 curing unit. I would suggest you cure them in water, This is what the manufacturer requires. All the B9 folks that I know cure their prints in water
Re: Curing Unit
I ordered two of the QUANS 110V 30W UV Ultra Violet High Power LED Lights this morning. will give a report
Re: Curing Unit
I have tried the smaller b9 unit under water and out of, they stay tacking when cured without water.
Under water 9 minutes small or large rings, really heavy silver men's rings have been casting well with only 9 minutes of light box cure, no microwave, no other cure method.
Using B9 resins only emerald and cherry
Under water 9 minutes small or large rings, really heavy silver men's rings have been casting well with only 9 minutes of light box cure, no microwave, no other cure method.
Using B9 resins only emerald and cherry
Re: Curing Unit
Thanks for your help
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Curing Unit
I've been using this one and it's really powerful. Cures prints fully in 30-60 min for most resins.
http://www.junction3d.com/buy/led-light-cure-box
http://www.junction3d.com/buy/led-light-cure-box
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Curing Unit
Looks like the B9. Maybe see if they can add buttons for preset times like the B9.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Curing Unit
There are 3 preset buttons. Can program them by holding the button down.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Curing Unit
max on the B9 box is 9 min. , can this one do an hour ? non stop ?
Who is online
Users browsing this forum: No registered users and 29 guests