Hi Mark,
No, the spring appeared to be well secured to the hole at the base, it was at the other end, where it appears to fit over the angled arm, that seems to attach to the tilt mechanism.
There did not appear to be any hole to secure it onto the arm, it looked like it just sat over the arm itself.
As you can tell from my description i did not actually fully remove the base to get a clear view of everything. I'd love to take a better photo, but i'm reluctant to move the printer as its working so well!
Print sticking to film
Re: Print sticking to film
Hi Mark, can you please help me out.
When homing the printer what i do is, loosen the 4 screws of the build platform, place a thin paper on the quarts, input $H, build platform goes down on the quarts, tighten the 4 screws, press +1 and then -1 to see that the paper is set tight on all 4 corners, press +50, press + 10, and print. I do this every time i restart CW. Because if i do like the manual says, just press $H, the build platform goes down on the quarts and i get a clicking noise and the controls don't let me put the build platform up, witch is the right way ?
Regards
Kerstien
When homing the printer what i do is, loosen the 4 screws of the build platform, place a thin paper on the quarts, input $H, build platform goes down on the quarts, tighten the 4 screws, press +1 and then -1 to see that the paper is set tight on all 4 corners, press +50, press + 10, and print. I do this every time i restart CW. Because if i do like the manual says, just press $H, the build platform goes down on the quarts and i get a clicking noise and the controls don't let me put the build platform up, witch is the right way ?
Regards
Kerstien
Re: Print sticking to film
You don't need to calibrate the build platform when you home ($h)! Just make sure to remove the build platform before homing and reinstall it after raising the arm up.
Re: Print sticking to film
reify wrote:You don't need to calibrate the build platform when you home ($h)! Just make sure to remove the build platform before homing and reinstall it after raising the arm.
Thanks Mark for all your help
Re: Print sticking to film
Can someone help me out with this, when im printing and the ring is peeling from the film it gets stuck so much that the ring bands when the platform rises and i get a bit of deformation and a lot of lines and some supports even fail but the ring still print.
Re: Print sticking to film
Have you wiped the film with anything abrasive like a paper towel?
Is this the original film? If not, the tension could be incorrect.
Is your exposure at the default (2800 ms for 30Z)?
Is this the original film? If not, the tension could be incorrect.
Is your exposure at the default (2800 ms for 30Z)?
Re: Print sticking to film
reify wrote:Have you wiped the film with anything abrasive like a paper towel?
Is this the original film? If not, the tension could be incorrect.
Is your exposure at the default (2800 ms for 30Z)?
Hi Mark, no i never use any kind of wipes, the film i changed it my self because i get dents in the film witch i don't know what made them, regarding the (2800 ms for 30Z) where do i find it in CW ? I will have a look in the morning when i get to the office.
Thanks Mark
Re: Print sticking to film
Kerstien wrote:reify wrote:Have you wiped the film with anything abrasive like a paper towel?
Is this the original film? If not, the tension could be incorrect.
Is your exposure at the default (2800 ms for 30Z)?
Hi Mark, no i never use any kind of wipes, the film i changed it my self because i get dents in the film witch i don't know what made them, regarding the (2800 ms for 30Z) where do i find it in CW ? I will have a look in the morning when i get to the office.
Thanks Mark
BTW Mark did you get my email with drop box ?
Re: Print sticking to film
Hi,
I did and replied a couple days ago but haven't heard back.
I did and replied a couple days ago but haven't heard back.
Re: Print sticking to film
reify wrote:Hi,
I did and replied a couple days ago but haven't heard back.
So you got the stl files via drop box ? Because i didnt get an email after that
Who is online
Users browsing this forum: No registered users and 40 guests