Problems with print
I ahve some issue with the printing... is giving me layera and bad surface on the prints
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Problems with print
Make sure your FULL RGB settings are enables, according to the instructions.
If they are, make sure you're mixing the resin bottle very well and shaking it for at least 2 minutes. It helps to drop some heavy marbles or some clean bolts inside the bottle and the shake. This is so that the pigment that may be settled on the bottom of the bottle can be reintegrated back into the resin.
If you did all that and still get the flashing, lower the Light Intensity Slider inside the resin profile, one notch at a time until the flashing goes away, and you're happy with the print quality.
If they are, make sure you're mixing the resin bottle very well and shaking it for at least 2 minutes. It helps to drop some heavy marbles or some clean bolts inside the bottle and the shake. This is so that the pigment that may be settled on the bottom of the bottle can be reintegrated back into the resin.
If you did all that and still get the flashing, lower the Light Intensity Slider inside the resin profile, one notch at a time until the flashing goes away, and you're happy with the print quality.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Problems with print
Also, which projector do you have?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Problems with print
mongerdesigns wrote:Also, which projector do you have?
Last week worked good. I printed with 42 resolution and aftet that changed to 25 and that s happenend
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Problems with print
25 micron XY setup puts out a little more energy since the projector is closer, so that makes sense.
Just adjust the intensity down a bit and it should be ok.
I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small details that require the 25 micron XY resolution.
We print at 42xy 99% of the time.
Just adjust the intensity down a bit and it should be ok.
I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small details that require the 25 micron XY resolution.
We print at 42xy 99% of the time.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Problems with print
mongerdesigns wrote:25 micron XY setup puts out a little more energy since the projector is closer, so that makes sense.
Just adjust the intensity down a bit and it should be ok.
I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small details that require the 25 micron XY resolution.
We print at 42xy 99% of the time.
I have vivitek 1188
I want to print some engagement rings will millgrain. And other filigree
Re: Problems with print
mongerdesigns wrote:25 micron XY setup puts out a little more energy since the projector is closer, so that makes sense.
Just adjust the intensity down a bit and it should be ok.
I do suggest printing at 42xy, because you get a large build area and the print quality is nearly the same unless you print really small details that require the 25 micron XY resolution.
We print at 42xy 99% of the time.
I just changed the preselected in options for 42. And the print got bad. Rings got oval.
After that changed back to 25 and this happenend.
Maybe i miss something
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Problems with print
You can't just select 42/25 and that's it, you need to change the projector distance, the lenses and recalibrate. Watch the videos again.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Who is online
Users browsing this forum: No registered users and 9 guests