Hey all
Got my souls set up (thanks Emil) been trying to make some prints but been shut out. None of the prints have come out.
I've checked the setting and even picked up a new vid card, specially suggested for the printer made all the changes but no luck.
Can it be exposing light time thing. Any advise thanks.
[SOLVED] Getting started failed prints
-
- Novice
- Posts:33
- Joined:Fri Dec 11, 2015 5:03 am
Re: Getting started failed prints
Can you post a pic?
Please PM me your email and I'll send you the sample ring we recommend printing first. This way we can figure out if it's your setup or the models.
Please PM me your email and I'll send you the sample ring we recommend printing first. This way we can figure out if it's your setup or the models.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Getting started failed prints
Did you change the nvidia settings to Full RGB like in the manual?
Did you remove the UV filter from the projector bulb?
Did you recalibrate the build table?
Did you remove the UV filter from the projector bulb?
Did you recalibrate the build table?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Getting started failed prints
If all you settings for computer and CW are correct, then it might be the tension of the vat on the quartz table. I found this to be one of my problems along with supports.
Get things set up like your going to print. Put the vat on without any resin in it. Press print. Make sure you are not tightening the vat too much. you should see the tilt mechanism operate.
Get things set up like your going to print. Put the vat on without any resin in it. Press print. Make sure you are not tightening the vat too much. you should see the tilt mechanism operate.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Getting started failed prints
He hasn't removed the UV filter. Just confirmed via email.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Getting started failed prints
Emil are you still using the economy setting in the projector settings?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Getting started failed prints
Yes.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:33
- Joined:Fri Dec 11, 2015 5:03 am
Re: Getting started failed prints
Okay so
Due to my ignorance, Emil reminded me about the projector filter. It did make a difference I put a quick
Design in and got something now printing the sample ring Emil sent me. Still might have to fine tune
Due to my ignorance, Emil reminded me about the projector filter. It did make a difference I put a quick
Design in and got something now printing the sample ring Emil sent me. Still might have to fine tune
-
- Novice
- Posts:33
- Joined:Fri Dec 11, 2015 5:03 am
Re: Getting started failed prints
Hey all got my first full print Thanks Emil for all the support still need to learn more
Re: Getting started failed prints
The number one thing I can tell you is that the support structure for the model is the most important.
Who is online
Users browsing this forum: No registered users and 46 guests