Projector changes distortion
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Update your software to version 1.2, if that doesn't fix it use English language windows. That's what's causing your issues.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Projector changes distortion
I updated to latest version
I changed system language to english (US)
Latest print same results
I changed system language to english (US)
Latest print same results
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Projector changes distortion
I think this might be caused by a bad bulb, or defective projector.
Can you please start the projector, then let it run for an hour or so. See if you can observe the change. Without printing. Simply project the grid.
Can you please start the projector, then let it run for an hour or so. See if you can observe the change. Without printing. Simply project the grid.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Projector changes distortion
Next print, same values as last (bad) print:
No deviation absolutely flawless. I always print this cylinder for documentaition purpose, so you can see the results.
Now I just run the test by simply projecting the grid. After half an hour there is no deviation visible.
Hope it stays that way.
No deviation absolutely flawless. I always print this cylinder for documentaition purpose, so you can see the results.
Now I just run the test by simply projecting the grid. After half an hour there is no deviation visible.
Hope it stays that way.
Re: Projector changes distortion
mongerdesigns wrote:I think this might be caused by a bad bulb, or defective projector.
Can you please start the projector, then let it run for an hour or so. See if you can observe the change. Without printing. Simply project the grid.
Almost seems like a distortion in the optical path of the projector post-DMD when it heats up.
None of the internals in the Solus can warp like that due to heat, right?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Projector changes distortion
Might be the lamp is not installed properly. Try to remove it and put it back in (make sure it's cold first and the projector is unplugged). As someone asked me once...no it's not ok if one of the screws keeps on turning. That mean it's not installed correctly.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Projector changes distortion
Just updated to the 1.2 contour version.
The grid still stays stabile. It seems this wodoo has ended.
By the way, the auto support tool is an absolute masterpiece.
Congratulation to the softwarewizards!!!!
The grid still stays stabile. It seems this wodoo has ended.
By the way, the auto support tool is an absolute masterpiece.
Congratulation to the softwarewizards!!!!
Who is online
Users browsing this forum: No registered users and 9 guests