Mis prints
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Residue or resin on the bottom of the tank or on the Quartz is big no no (because: optical surface)
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Mis prints
So what can I use to get it off the quartz. I tried a little dawn on damp pec pad. Followed by alcohol l. Still a little film/residue.
Also would this be why it printed the whole gird?
Also would this be why it printed the whole gird?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Mis prints
Definetly not dawn. I use 90% alcohol from the drug store and a paper towel on the Quartz. For the bottom of the tank use pec pads with some alcohol instead of paper towels. Paper towels will scratch the film.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Mis prints
If it printed the entire build area then you need to check your graphics card settings as described in part 1 of the manual.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Mis prints
Will check to see if my settings got changed somehow.
After getting to top of the table clean I notice the underside also had a film on it along with the mirror. Had some resin seep inside and guessing the fumes cause the residue. All clean now.
After getting to top of the table clean I notice the underside also had a film on it along with the mirror. Had some resin seep inside and guessing the fumes cause the residue. All clean now.
Re: Mis prints
Have you checked these out in Netfab?
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Mis prints
Yes it went through netfab.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Mis prints
Did a print today and it came out great. That is after I fixed my settings for the display adapter. Thanks for suggesting Emil. Figured it was going to be computer related.
I swear a ghost lives in Windows 10. Not only where mys settings changed, but Cortana switched back on. I have tried to disable all extra junk running.
I swear a ghost lives in Windows 10. Not only where mys settings changed, but Cortana switched back on. I have tried to disable all extra junk running.
Re: Mis prints
Its amazing what is always running on a computer. I have tried to remove as much stuff as I can o0n my laptop for the Solus. The more junk I remove the more consistent the prints are. What is worse the newer laptops have all the App crap and it is loaded with blotware. I think I finally have most of that removed as well. Mark
Jewelermdt wrote:Did a print today and it came out great. That is after I fixed my settings for the display adapter. Thanks for suggesting Emil. Figured it was going to be computer related.
I swear a ghost lives in Windows 10. Not only where mys settings changed, but Cortana switched back on. I have tried to disable all extra junk running.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: Mis prints
Instead of making a new post I post here. Was printing a pendant today and look at printer and the platform was all the way up. So figured it was done. Soon as I walked back there it went down in a hurry. Thought I was going to have a broken quartz. I notice it was at 107% complete. I swear I have gremlins in my computer.
[img] [/img]
[img] [/img]
- Attachments
-
- 107percent.JPG (13.94KiB)Viewed 12138 times
Who is online
Users browsing this forum: No registered users and 10 guests