HI,
Advice how to put less supports so i don't get mirco prongs to clean....
https://drive.google.com/file/d/0B0kqKa ... =drive_web
auto support on mirco prongs heavy ring
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: auto support on mirco prongs heavy ring
That's a tough one. I would go and manually put 0.1mm supports on those prongs that point down.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: auto support on mirco prongs heavy ring
Hard to say, but I don't think so. If you support a few prongs then most likely all of them on the same row need to be supported. Use the slider on the right to see if there are any "islands" popping up created by the prong tips.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: auto support on mirco prongs heavy ring
i think last i did which image above it was on ring support it grow almost nicely only 1 part at sdie top failed....
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: auto support on mirco prongs heavy ring
I think the best way is to print it in two pieces like the pictures below, then put them back together before casting.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: auto support on mirco prongs heavy ring
Nice suggestion, Sam.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: auto support on mirco prongs heavy ring
I was going to suggest printing it upside down. Don't think tilting would help. Would have a lot of supports on one side.
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: auto support on mirco prongs heavy ring
I tried it upside down, Mike, but still have a lot of prong pointing downward on the side of the shank.
Jewelermdt wrote:I was going to suggest printing it upside down. Don't think tilting would help. Would have a lot of supports on one side.
Who is online
Users browsing this forum: No registered users and 14 guests