hello everyone,
Ring seems came out ok, but pendant failed seems support was less or what i don't no....you can see below images ring marks on film after i drain resin i saw to take picture i kept on printer easier to see..
there is pear shape green build on film i removed i don't see mark of that pear like how deep ring u see....same problem happen with early ring 3 times i did failed, 4th time i did print ok but while drain resin design marks on film i try to remove then film gets marks so i replace.......
advice shall i remove that ring mark from film or not,, if yes how to do....we don't have pec-pad....before i clean with len tissues i had to replace film as others are using 1 film few months.
support program B9.
would be thankful if you guide me.
Film marking and build support problem
-
- Posts:8
- Joined:Mon Nov 02, 2015 9:25 pm
Re: Film marking and build support problem
The support tips on the pendant look too thin or small. You kind of have to imagine when it gets to those layers that there will barely be anything to "catch on to", try making them thicker. And for the sticking maybe the film tension is too loose. But it looks like a exposure time issue or rgb issue. I see some flashing at the base of the pendant and ring. In your Contour picture it looks like the base has rounded hill edges but the print shows a perfect pear shape. Double check your RGB settings and if that is correct lower your exposure time by maybe .4 milliseconds. I adjusted my base layer exposure time from 16 sec to 5 sec and overall exposure time from 2.7 sec to 2.3. This got rid of the flashing, sticking, and shrapnel. I hope this helps.
Last edited by MarkPhilip on Thu Aug 18, 2016 2:26 am, edited 1 time in total.
Re: Film marking and build support problem
hi,
when i received printer same problem happen on film 2 print came out good no problem, then ring was done twice failed 3rd time came out ok but not 100% tiny prongs was not clear but on film marks of ring design.....so i wipe then more problem started so i replace new film i did print ring came out ok, pendant failed.....attached image of my setting....
after good printing is done cleaning and microwave 3mins, cool down 10mins same 3times curving is done then hang outside window for 1-2days direct sun light then i cut supports ring looks not round looks slight oval and some flat like map gets bend... still it's soft samples i had they r harder, main is soft...
when i received printer same problem happen on film 2 print came out good no problem, then ring was done twice failed 3rd time came out ok but not 100% tiny prongs was not clear but on film marks of ring design.....so i wipe then more problem started so i replace new film i did print ring came out ok, pendant failed.....attached image of my setting....
after good printing is done cleaning and microwave 3mins, cool down 10mins same 3times curving is done then hang outside window for 1-2days direct sun light then i cut supports ring looks not round looks slight oval and some flat like map gets bend... still it's soft samples i had they r harder, main is soft...
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Film marking and build support problem
You don't want any overhang . Place you adequate supports where needed . I Always do adjustments whenever I check my work a second time. less frequency of job failure.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: Film marking and build support problem
I wish if the moderator can make few videos on how to add your supports . New to the printing will have an easy ride with solus. I see most complaints are related.
Re: Film marking and build support problem
half print, are my support OK?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Film marking and build support problem
It seems like a computer issue or a bad mesh causes a slice failure.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Film marking and build support problem
Check your power saving settings (especially USB selective suspend) and screen saver. Make sure your Windows auto update is turned off.
Re: Film marking and build support problem
We have configured correctly.
there is no marks on film, even last ring marks gone it self....
there is no marks on film, even last ring marks gone it self....
Re: Film marking and build support problem
If there's nothing stuck to the film it sounds like your projector stopped projecting. Any chance you had another power interruption? Are you using a VGA or HDMI cable? Did you check your screen saver and external monitor power savings settings? Did you check the slice images before printing?
Who is online
Users browsing this forum: No registered users and 31 guests