help
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
In unpacking I put my power supply to the side and it was on top of another machine. I want to be sure it is correct one to use. AC/DC Model HHWY1201 output 12VDC
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: help
OK found the right one. Only difference is the one that comes with it is rated 12V 2A My other one was 12V 1A
Now if I could only get things to work.
Now if I could only get things to work.
Re: help
Emil will be able to get you sorted when he gets into the office.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: help
Have not had a lot of time to check out my setup. But today I did notice that my close up lens does not fit snug on the projector lens. It tilts about 2 to 3mm. Guessing this will cause blurred / out of focus images. Will work on that tomorrow. Tried a wide rubber-band on P lens but it was too thick.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: help
found some Adhesive tape for a "Command" hook. Just the right thickness I needed. Looks like it will work to hold it tighter on the projector just fine. Trying a new print today.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: help
That's good you found a solution. I was gonna offer to send you some felt tape that you can cut and paste inside the lens holder for a more snug fit.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- MobiusJewelryDesign
- Novice
- Posts:55
- Joined:Sat Sep 19, 2015 12:30 pm
- Location:Atlanta, GA
- Contact:
Re: help
Help! The material is sticking to the film and not the vuild plate!
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: help
My problem also. usually it's because of not enough supports or they are in the wrong place.
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: help
Finlay had time to look at the projector and printer today. First went and check all setting and focus for the projector. Not sure I have an issue. Using the 42xy 80x45 grid, to focus the lens it turns all the way clockwise I believe. The lines look focused but wondering if I should have some more play?
Also I found out not to put your paper on top of quartz table before looking at the gird lines. Mine where going off and down the right sides and not in middle of table top. Guessing my cabinet top is not as level as it needs to be. So after adjusting the projectors feet I got the calibration grid to be in center.
Tomorrow I will see if this solves my problems.
Mike
Also I found out not to put your paper on top of quartz table before looking at the gird lines. Mine where going off and down the right sides and not in middle of table top. Guessing my cabinet top is not as level as it needs to be. So after adjusting the projectors feet I got the calibration grid to be in center.
Tomorrow I will see if this solves my problems.
Mike
Who is online
Users browsing this forum: No registered users and 4 guests