auto support on mirco prongs heavy ring

General topics about 3d printing.
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm
Re: auto support on mirco prongs heavy ring

Postby rsaldivar » Sat May 27, 2017 5:24 pm

Emil , would you recommend including the sprues to be grow in the file with this resin ??
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: auto support on mirco prongs heavy ring

Postby mongerdesigns » Sat May 27, 2017 6:08 pm

Sure, you can do that. But might take longer to grow depending on the position of your sprue.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
rsaldivar
Solus Master
Posts:327
Joined:Tue Jun 30, 2015 8:51 pm

Re: auto support on mirco prongs heavy ring

Postby rsaldivar » Sat May 27, 2017 6:49 pm

also , will contour ever have an option for not raising or limiting the heith of the tallness of the grow, I mean being able to control the height of the model being raised and adding more time to the grow , or is that height been shown to have the most success rate as a result ??
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: auto support on mirco prongs heavy ring

Postby mongerdesigns » Sun May 28, 2017 3:21 am

dcpattni wrote:@ mongerdesigns,

Request can you plz try with new resin (SOLUS blue resin) ring which I posted......also share supports sizes etc.


Don't have much time but it was interesting to see how it would pull it off. No sweat. The support tips are the smallest at 0.1 and automatic supports were used.

Hope you don't mind if I take this print to the JCK :)

https://instagram.com/p/BUnuJ8lDMSN/
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
samatheang
Solus Expert
Posts:197
Joined:Wed Feb 17, 2016 10:36 pm

Re: auto support on mirco prongs heavy ring

Postby samatheang » Sun May 28, 2017 6:20 am

That's sooo coool! :D
Dieter
Novice
Posts:42
Joined:Sun Jan 17, 2016 3:19 pm

Re: auto support on mirco prongs heavy ring

Postby Dieter » Sun May 28, 2017 6:57 am

Now perfect casting and you have a winner!!
Can't wait to have the blue stuff...
dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:

Re: auto support on mirco prongs heavy ring

Postby dcpattni » Sun May 28, 2017 10:25 am

@ mongerdesigns

Print is wow wow wow.....and autosupport @0,1mm is also wow!!!!!
i don't mind atall.....thank you very much for trail print.

I love my Solus printer!!!.
User avatar
M-Williams
Solus Master
Posts:393
Joined:Sun Nov 01, 2015 4:45 pm

Re: auto support on mirco prongs heavy ring

Postby M-Williams » Sun May 28, 2017 2:36 pm

You can't go wrong with countour. you need just to pay attention to any overhang .
dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:

Re: auto support on mirco prongs heavy ring

Postby dcpattni » Wed May 31, 2017 8:05 pm

hi,

after suggestion from SOlUS users experts i try as below:-

1st try single ring white 0.1mm support which print good easy to removed supports but bottom(dome area) prongs it was not perfect.

2nd try in 2 parts as Mr.Sam advice, it worked very clear but top front only it did not print well....but rest was clean & clear images below.

3rd try with 0.2mm only for Dome it didn't grow....

All suports are manualy.

I always mix b9 very very well before filling in VAT.

what do you think........i m doing few other printing going OK....only this ring mirco prongs giving tuff time.
Attachments
1-DSC_3345.JPG
2nd try in 2 parts as Mr.Sam advice
5-DSC_3351.JPG
2nd try in 2 parts as Mr.Sam advice
3-DSC_3349.JPG
2nd try in 2 parts as Mr.Sam advice
2-DSC_3348.JPG
2nd try in 2 parts as Mr.Sam advice
IMG_20170531_220932894.jpg
3rd try with 0.2mm support, it didn't grow....
dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:

Re: auto support on mirco prongs heavy ring

Postby dcpattni » Wed May 31, 2017 8:08 pm

clearly seen dome area prongs are not good.
Attachments
Capture.JPG 45.JPG
3rd try
DSC_3339.jpg
1st try single pring 0.1mm supports in all prongs, easy to remove.

Who is online

Users browsing this forum: No registered users and 6 guests