using scences
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
I did some scenes in 1.2, updated to 1.3. Will not load them? Do I have to redo them in 1.3?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: using scences
Yes, because it was a major upgrade (supports).
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: using scences
Well now that you say that, my scenes were with supports.
I had an update to computer even though I have it turn off. RGB is set to full. had a print just fail. AM trying it again. it also crashes when trying to open this stl file. I can't attached/upload file. https://www.dropbox.com/s/1fmg2m4tofruwom/base.stl?dl=0
I had an update to computer even though I have it turn off. RGB is set to full. had a print just fail. AM trying it again. it also crashes when trying to open this stl file. I can't attached/upload file. https://www.dropbox.com/s/1fmg2m4tofruwom/base.stl?dl=0
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: using scences
I was using the older version. The stl that crashed Contour was due to it being saved in matrix below X plane. I guess Contour can't figure that it need to pull it up. Also when it crashed it changed by background for windows to black.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: using scences
Your background should be black anyway.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: using scences
The background on my laptop for the printer is. But I design at home, and was setting up for printing the next day.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: using scences
It should only turn it black when running contour.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Re: using scences
when Contour crashed, it kept the black background for windows.
It would be nice when using auto supports to choose NO base supporting. When printing rings I like my own support base to use for casting. I get around this by having a separate base file and deselecting it for supports. A lot of extra steps.
It would be nice when using auto supports to choose NO base supporting. When printing rings I like my own support base to use for casting. I get around this by having a separate base file and deselecting it for supports. A lot of extra steps.
Who is online
Users browsing this forum: No registered users and 63 guests