***Totally Stoked!!***

Show off your prints.
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina
Re: ***Totally Stoked!!***

Postby Archerm » Fri Jul 14, 2017 2:34 pm

A few castings from yesterday. All were emerald prints cast using Plasticast.

Image
dcpattni
Novice
Posts:97
Joined:Sat May 07, 2016 4:55 pm
Location:Dar-es-salaam,TANZANIA
Contact:

Re: ***Totally Stoked!!***

Postby dcpattni » Fri Jul 14, 2017 7:50 pm

Hello Mark

Top class print & casting you get always.....i.m dont get same for rings it gets lines i need to fill up with super glue or wax to make levelling......if possbile can you share yr setting for 80x45- 25z or 20z....

DId try 2mm rod same height they comes out nice.

https://drive.google.com/file/d/0B0kqKa ... sp=sharing
Attachments
25z.JPG
setting i'm using
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Mon Jul 17, 2017 2:46 am

I will check monday.
User avatar
rkundla
Solus Master
Posts:308
Joined:Sat Jan 09, 2016 6:01 am

Re: ***Totally Stoked!!***

Postby rkundla » Mon Jul 17, 2017 6:39 pm

mongerdesigns wrote:I don't think that's overcure. His build tables are probably calibrated a little too close. So it's compression of the first few layers.


Ahh, I didn't think of that. :-P
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Mon Jul 17, 2017 7:39 pm

dcpattni wrote:Hello Mark

Top class print & casting you get always.....i.m dont get same for rings it gets lines i need to fill up with super glue or wax to make levelling......if possbile can you share yr setting for 80x45- 25z or 20z....

DId try 2mm rod same height they comes out nice.

https://drive.google.com/file/d/0B0kqKa ... sp=sharing


Image
User avatar
M-Williams
Solus Master
Posts:393
Joined:Sun Nov 01, 2015 4:45 pm

Re: ***Totally Stoked!!***

Postby M-Williams » Fri Jul 21, 2017 6:16 pm

Thank you for sharing.
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Jul 26, 2017 2:44 pm

I have a few two tone helicoil rings to finish up for next week. This will be the white gold helicoil insert. there will be a yellow gold cap on each end of the helicoil. Designed with a constant .5mm overall wall thickness and so the only support needed is the .5 mm fin support around the bottom.

Image

Image
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Aug 02, 2017 8:12 pm

A few prints from today!! :mrgreen:

Image

Image

Image

Image

Image

Image

Image
Dstonic
Novice
Posts:54
Joined:Thu Mar 09, 2017 1:52 pm
Location:Breaux Bridge, Louisiana

Re: ***Totally Stoked!!***

Postby Dstonic » Sun Aug 06, 2017 8:04 pm

Mark, Absolutely outstanding !!!!
What resolution do you normally use , 48x27 or 80x45 ? Reason I ask, a few post back you showed your settings for 80x45.......I've had a issue growing a 12 mm wide ring size 13+ and it took up the whole scene. Should I have switched to 80x45? Thanks...>David
User avatar
Jewelermdt
Solus Master
Posts:809
Joined:Sun Jul 19, 2015 10:38 pm
Location:N.W. Florida
Contact:

Re: ***Totally Stoked!!***

Postby Jewelermdt » Mon Aug 07, 2017 2:04 am

Hey David
He has 2 printers. One set up for each size.
If you have room all around the ring, it should print fine. Just use a lot of supports. Even half way up on side of ring to keep it from sagging mid print.

Who is online

Users browsing this forum: No registered users and 6 guests