***Totally Stoked!!***
Are you using the solus software if so>>>> Go to the profile page of the resin you are using buffer is in the lower right corner mine was set to one. I bumped it up to three and it made a huge difference on both 25xy and 42xy machines.
Re: ***Totally Stoked!!***
Sorry for the jewelers hands!!
https://www.youtube.com/watch?v=7XK_QhrnzJY
https://www.youtube.com/watch?v=7XK_QhrnzJY
Last edited by Archerm on Fri Sep 02, 2016 4:00 pm, edited 1 time in total.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: ***Totally Stoked!!***
Looks amazing!
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: ***Totally Stoked!!***
Archerm wrote:Are you using the solus software if so>>>> Go to the profile page of the resin you are using buffer is in the lower right corner mine was set to one. I bumped it up to three and it made a huge difference on both 25xy and 42xy machines.
Thank you for your reply, Mark. Does changing the buffer up to three make it takes longer to print? Thanks.
Re: ***Totally Stoked!!***
Yes 3 seconds a layer if you use 3.
samatheang wrote:Archerm wrote:Are you using the solus software if so>>>> Go to the profile page of the resin you are using buffer is in the lower right corner mine was set to one. I bumped it up to three and it made a huge difference on both 25xy and 42xy machines.
Thank you for your reply, Mark. Does changing the buffer up to three make it takes longer to print? Thanks.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: ***Totally Stoked!!***
I would like to add that changing the buffer to a high number like that is not always necessary. In fact 99% of the time it's not needed, and simply just takes longer to print.
The reason it works well in the case of this band, is because it's sitting flat and that slows down the flow of resin. A longer buffer time simply waits longer for the resin to stop moving before exposing the next layer, giving you sharper details.
I think 2 seconds might have had the same effect.
The reason it works well in the case of this band, is because it's sitting flat and that slows down the flow of resin. A longer buffer time simply waits longer for the resin to stop moving before exposing the next layer, giving you sharper details.
I think 2 seconds might have had the same effect.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: ***Totally Stoked!!***
Thank you for the reply, Mark and Emil.
Re: ***Totally Stoked!!***
Fantastic work Mark! Very inspiring for all of us here.
Who is online
Users browsing this forum: No registered users and 9 guests