***Totally Stoked!!***

Show off your prints.
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:
Re: ***Totally Stoked!!***

Postby mongerdesigns » Wed Feb 06, 2019 5:23 pm

Excellent work as usual and supports. Just so you know Mark, we're training an AI to replicate your supports work.... jk....or am I? :)
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Thu Feb 07, 2019 2:38 am

:mrgreen: You know me I am a support minimalist!! :geek:
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Nov 27, 2019 1:10 am

Been a while since I printed on my 25xy Solus so I fired it up the past few days. Here are a few prints for you to enjoy! :mrgreen: :mrgreen: :mrgreen:

Image

Image

Image

Image
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Nov 27, 2019 1:24 am

Image

Image

Image

Image
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Nov 27, 2019 1:28 am

Image

Image

Image

Image
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Nov 27, 2019 1:32 am

Image

Image

Image

Image
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Wed Nov 27, 2019 1:46 am

Image

Image

Image

Image

Image
Kokos
Novice
Posts:30
Joined:Sat Dec 29, 2018 10:38 am

Re: ***Totally Stoked!!***

Postby Kokos » Wed Nov 27, 2019 3:53 pm

Thank you for showing the Rhino picture!!! The prints pictures are often showed. But not the "secret sauce" :)

Will this extruding technique also work with rings with prongs on the sides?
User avatar
Archerm
Solus Master
Posts:599
Joined:Mon Oct 26, 2015 1:57 pm
Location:North Carolina

Re: ***Totally Stoked!!***

Postby Archerm » Thu Nov 28, 2019 1:09 am

Kokos wrote:Thank you for showing the Rhino picture!!! The prints pictures are often showed. But not the "secret sauce" :)

Will this extruding technique also work with rings with prongs on the sides?

Yes it will. It is very easy and fast. You just have to be careful trimming them. I trim them about 1mm then lightly sand them down to about .1 mm. Then after casting sand off the rest.
Kokos
Novice
Posts:30
Joined:Sat Dec 29, 2018 10:38 am

Re: ***Totally Stoked!!***

Postby Kokos » Thu Nov 28, 2019 1:11 pm

When I have I ring with prongs, I will try your method. Now I am always messing about.

Who is online

Users browsing this forum: No registered users and 12 guests