Just adding pictures of some of the things I print. A lot of my work is not open to sharing since its customer driven. I was not able to share my first 2 prints because of copyrighted logos, but here is a clip for a custom pen and A rollstop for a pen.
The rollstop is 10mm high and 11.5 wide.The writing is .6mm tall. My photo skills need worked on.
Some of my works
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Some of my works
Awesome prints. You didn't even need help setting up.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Some of my works
I cast the two pieces, actually a couple of each I almost always print doubles or even triples in case something goes wrong.
The clip did not come out as well as I would have liked. THe casting was slightly rough but I didnt like the way the grid came out. s
So I changed it and printed a new one to cast.
THe roll stop looks much better in person. I may have to set up a light tent to get a better picture.
The clip did not come out as well as I would have liked. THe casting was slightly rough but I didnt like the way the grid came out. s
So I changed it and printed a new one to cast.
THe roll stop looks much better in person. I may have to set up a light tent to get a better picture.
Last edited by mredburn on Tue Jul 14, 2015 3:03 pm, edited 1 time in total.
Re: Some of my works
Here is the new clip with a finer pattern inside, the grid is made up of .5mm round bars.
The white glistening is from Mineral oil where I zapped it in the microwave to help cure the resin, not from holes in the print.
The white glistening is from Mineral oil where I zapped it in the microwave to help cure the resin, not from holes in the print.
Re: Some of my works
Trying to get a better shot of the roll stop, Its actually polished and hard to photo.
Its only 10mm tall and 11mm wide. It is an opened book so the vertical lines on the sides are pages not print defects.
Lets see if these show it better
Its only 10mm tall and 11mm wide. It is an opened book so the vertical lines on the sides are pages not print defects.
Lets see if these show it better
Re: Some of my works
A couple of center bands for pens and a basket weave pattern I wanted to try.
This is a simple design, they are 8mm tall, 12.25mm in diameter, With a 6.54mm hole
I wanted to see how this would print. I will use the file to add the basket weave to the surfaces of centerbands and clips.
each segment is 1.6 x 1.8mm, the sheet of them is .63mm thick.
It was printed vertically with a 1mm wide x .5mm tall bar attached to the bottom of the weave for printing.
There is some loss in the one corner where it was basically unsupported.
THere is some filling in of the holes in the pattern in the upper right hand side, and a little bit along the bottom left between
the bottom bar and the horizontal segments.
I will have to try and cast it.
This is a simple design, they are 8mm tall, 12.25mm in diameter, With a 6.54mm hole
I wanted to see how this would print. I will use the file to add the basket weave to the surfaces of centerbands and clips.
each segment is 1.6 x 1.8mm, the sheet of them is .63mm thick.
It was printed vertically with a 1mm wide x .5mm tall bar attached to the bottom of the weave for printing.
There is some loss in the one corner where it was basically unsupported.
THere is some filling in of the holes in the pattern in the upper right hand side, and a little bit along the bottom left between
the bottom bar and the horizontal segments.
I will have to try and cast it.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Some of my works
Wow. I love that how you supported those bands at an angle. Only give you a tiny spot that needs work/cleanup. Did you try printing it just flat on the build platform with no supports?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Some of my works
THe support will become the sprue for casting. I could have printed them flat with the sprue at an angle but I wanted to try it this way.
Re: Some of my works
Didn't see these pics until now Mike. The centerbands look perfect.
Who is online
Users browsing this forum: No registered users and 6 guests