Emil and Mark!! This 3d printer is absolutely great!!! So I was sitting at my Cad computer this morning and had a few minutes to burn sooooo I put this together really quick. I wanted to test the printer to see if this would print on the 42xy build at .020. I wanted to do it with minimal support. The project measures 60mm X 20mm The only supports are one on the bottom of each helix wire curve. No supports between any of the helix coils. These are intertwined and will be all connected and flexible when the supports are removed. The supports are 1mm diameter with a cone attached footprint of .25mm to the piece. The piece itself is 1mm diameter wire helix coils. I will tell you I am in Ah of this printer. On a side note the B9 emerald resin has just been great.
I Have a bone to pick with .....
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: I Have a bone to pick with .....
Mark, that's really cool looking!
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: I Have a bone to pick with .....
Whats neat is when the supports come off it will still be connected but flexible. but it wont come apart.
Re: I Have a bone to pick with .....
A few videos for Emil.
https://www.youtube.com/watch?v=OWVMp3_Rk1c&feature=youtu.be
https://www.youtube.com/watch?v=690_diFowrA
https://www.youtube.com/watch?v=OWVMp3_Rk1c&feature=youtu.be
https://www.youtube.com/watch?v=690_diFowrA
Last edited by Archerm on Fri Feb 19, 2016 1:37 pm, edited 11 times in total.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: I Have a bone to pick with .....
The videos are private. Can't view.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: I Have a bone to pick with .....
Can I embed them? How?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: I Have a bone to pick with .....
Click on the little play button on the top bar when you are writing a message and paste the YouTube link.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: I Have a bone to pick with .....
Finally got it.
Re: I Have a bone to pick with .....
Now lets see you cast them
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
Re: I Have a bone to pick with .....
Casting this piece would actually be pretty easy. If I were going to cast it I would have angled all the supports 25 degrees the same direction oriented down towards one end. I would have made the supports the same diameter from the base to the helix(no taper at the helix). Then I would have added a main support to connect the supports on each helix coil joining the main supports at one end of the piece. This would act as the main sprue. I would have grown the piece with all the above included in the print. If I get a chance in the future I will cast one. Pretty busy right now.
darrinfry wrote:Now lets see you cast them
Who is online
Users browsing this forum: No registered users and 9 guests