Finally switched to Emerald
So i finally switched to emerald. Gotta say i like it.
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Finally switched to Emerald
Wow, Darrin. That looks incredible! Keep it going.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Finally switched to Emerald
This is a memorial charm for a client who had a granddaughter pass away. Text on the outside goes 320 degrees around it, with hand prints on one side and footprints on the other. 2mm thick 25mm in diameter. The lettering on the outside averages 1mm tall with average width of the cut ins being .25mm.
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Finally switched to Emerald
Impressive.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Finally switched to Emerald
VERY NICE! You nailed it!!
I'm SURE it will have GREAT meaning to the owner. Sad memorial, bitter sweet. You made the sweet part....
Bob
I'm SURE it will have GREAT meaning to the owner. Sad memorial, bitter sweet. You made the sweet part....
Bob
Re: Finally switched to Emerald
Unfortunately we do a lot of things like this. Our owners brother is one of the morticians in our area and suggests things like this to his clients. This is the first we have tried to put text on the side of the piece. We also used to do these on our Revo CX, which now sits eerily quiet.
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
-
- Novice
- Posts:12
- Joined:Fri Jun 03, 2016 8:16 pm
- Location:Raleigh, NC
- Contact:
Re: Finally switched to Emerald
Hey there! I'm just curious, it doesn't look like you had any supports in the middle of the medalion, is that right? Did you have any sagging?
I'm trying to figure out the magic of proper supporting so I'm trying to glean as much as I can from everyone's successful prints!
I'm trying to figure out the magic of proper supporting so I'm trying to glean as much as I can from everyone's successful prints!
Bailey's Fine Jewelry
Custom Design and Service Dept
Custom Design and Service Dept
Re: Finally switched to Emerald
There where only a few supports in the middle, and each one connects with a point of .30mm. To help prevent the sagging it is tilted at a 45 degree angle. Each of the letters that faced down had a support too, which helped. With this specific piece i choose not to put lots of supports on the middle to help with clean up. With my supports i remove them just after cleaning the piece with a scalpel.
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
Re: Finally switched to Emerald
I am still a fan of the straight emerald. Maybe someday i will be adventurous and mix it. If its not broke don't fix it. And mark my words, the alternative diamonds are on the rise.
I really don't have any dogs. But the insatiable urge to fit in has caused me to do a dog avatar!
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Finally switched to Emerald
Very nice.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Who is online
Users browsing this forum: No registered users and 6 guests