first prints with Maker Juice

Show off your prints.
User avatar
Just Bob
Novice
Posts:72
Joined:Fri Mar 25, 2016 4:37 pm
first prints with Maker Juice

Postby Just Bob » Tue Apr 26, 2016 2:01 pm

Nice and smooth. Hard to take a good pic bc of the color.

Just Bob
Attachments
2016-04-25 17.53.52.jpg
2016-04-25 18.44.30.jpg
User avatar
Just Bob
Novice
Posts:72
Joined:Fri Mar 25, 2016 4:37 pm

Re: first prints with Maker Juice

Postby Just Bob » Tue Apr 26, 2016 2:02 pm

2016-04-26 07.10.34.jpg
lklutts
Solus Expert
Posts:124
Joined:Thu Jul 16, 2015 8:48 pm

Re: first prints with Maker Juice

Postby lklutts » Tue Apr 26, 2016 4:15 pm

Looking good Bob
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: first prints with Maker Juice

Postby mongerdesigns » Tue Apr 26, 2016 5:02 pm

Those look good Bob. Do you have issues with it sticking to the plate? Seems like I have to make the bases huge so the pieces stay in place.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/
User avatar
sgraber
Novice
Posts:15
Joined:Tue Apr 05, 2016 1:03 pm

Re: first prints with Maker Juice

Postby sgraber » Thu May 05, 2016 8:35 pm

mongerdesigns wrote:Those look good Bob. Do you have issues with it sticking to the plate? Seems like I have to make the bases huge so the pieces stay in place.


Try dropping your <LiftFeedRate>150</LiftFeedRate> down to something like <LiftFeedRate>25</LiftFeedRate>. It's possible you're pulling too fast. I do all of mine @ 25 LiftFeedRate and 500 ReturnFeedRate and I have zero problems.
User avatar
mongerdesigns
Solus Guru
Posts:1950
Joined:Sat Apr 25, 2015 5:16 pm
Location:Los Angeles
Contact:

Re: first prints with Maker Juice

Postby mongerdesigns » Thu May 05, 2016 10:56 pm

sgraber wrote:
mongerdesigns wrote:Those look good Bob. Do you have issues with it sticking to the plate? Seems like I have to make the bases huge so the pieces stay in place.


Try dropping your <LiftFeedRate>150</LiftFeedRate> down to something like <LiftFeedRate>25</LiftFeedRate>. It's possible you're pulling too fast. I do all of mine @ 25 LiftFeedRate and 500 ReturnFeedRate and I have zero problems.


Tried slowing it down, the problem is not pulling too fast. Even prints that do stick, I can remove by just sliding them off of the build plate with my finger.
Tried overcuring the base layer, which helps a little, but creates big overflashing and also delamination past the base layers.

P.S. Those settings are useless for Solus users. They are called something else in CW. Please don't confuse people.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com

Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com

Follow us on Instagram!
https://www.instagram.com/junction3d/

Who is online

Users browsing this forum: No registered users and 12 guests