Autumn Tree

Show off your prints.
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm
Re: Autumn Tree

Postby M.A.N » Thu Oct 20, 2016 8:36 pm

nillard wrote:I am having a TERRIBLE time trying to cast a 14k WG bracelet. Either chunks of investment remain on the inside
or it seems like the Plasti-Cast breaks down at a point and dosent remain to its form of the bracelet. Its a thick bracelet
All in its 2.5dwt in resin so its a big casting... Think this investment will help? Here's a pic from todays 3rd casting that didnt work.
EVERYTHING else I do is perfect.

This link has a 360 pic! https://spinzam.com/shot/?idx=3520
https://spinzam.com/shot/?idx=3520


M.A.N wrote:
mongerdesigns wrote:Did you use this investment? http://www.stuller.com/products/22-4748/?groupId=192169

I heard good things about it.

Yes.
Its really a good investment.

Yes. I think your problem will be solve cause your cast pic is like my casted models before i switch to optima.
rkundla wrote:Does it require any special steps or does it behave like Kerr SatinCast?

What burnout program did you use to get those results?

Normally I wouldn't buy that kind of stuff from Stuller, but when my box of PlastiCast runs out, I'd consider giving it a try. ;)

Its like satin cast but not in resin casting result. It has really smooth surface.
It has a special burnout cycle on its pdf(added below)
(Note:Leave flask for 3 hours after pouring investment in it)
But you can use your normal burnout cycle. Just you have to stay in 780c-800c degrees for 2 hours before going to cast temp. You know to let resin burn completely.
And its investment mixing is in pdf too.
Attachments
tmp_861-optima-995087060.pdf
(834.51KiB)Downloaded 604 times
nillard
Novice
Posts:46
Joined:Fri Jun 10, 2016 9:58 pm

Re: Autumn Tree

Postby nillard » Wed Nov 16, 2016 9:32 pm

http://www.stuller.com/products/22-4748 ... SiteSearch

WORKED GREAT ON THIS HEAVY 14k Cuff!!!

https://spinzam.com/shot/?idx=5211





nillard wrote:I am having a TERRIBLE time trying to cast a 14k WG bracelet. Either chunks of investment remain on the inside
or it seems like the Plasti-Cast breaks down at a point and dosent remain to its form of the bracelet. Its a thick bracelet
All in its 2.5dwt in resin so its a big casting... Think this investment will help? Here's a pic from todays 3rd casting that didnt work.
EVERYTHING else I do is perfect.

This link has a 360 pic! https://spinzam.com/shot/?idx=3520
https://spinzam.com/shot/?idx=3520


M.A.N wrote:
mongerdesigns wrote:Did you use this investment? http://www.stuller.com/products/22-4748/?groupId=192169

I heard good things about it.

Yes.
Its really a good investment.
M.A.N
Novice
Posts:39
Joined:Fri Apr 15, 2016 4:54 pm

Re: Autumn Tree

Postby M.A.N » Thu Nov 17, 2016 6:40 am

Very well ;)
User avatar
MobiusJewelryDesign
Novice
Posts:55
Joined:Sat Sep 19, 2015 12:30 pm
Location:Atlanta, GA
Contact:

Re: Autumn Tree

Postby MobiusJewelryDesign » Fri Nov 18, 2016 1:18 am

That's amazing!

Who is online

Users browsing this forum: No registered users and 7 guests