ResinWorks EasyCastHD castable resin

Discuss 3d printing resins
rsaldivar
Solus Expert
Posts: 282
Joined: Tue Jun 30, 2015 8:51 pm

Re: ResinWorks EasyCastHD castable resin

Postby rsaldivar » Thu Mar 07, 2019 5:42 am

that was my fist time growing and casting it , I did a 45 min. boil in water anniel , a 10 min. uv cure , 2 hours sit time with optima and a straight ramp to 1500 f for a total time in the oven of 6 hours , down to cast temp and this is my results , will try different thing next time , I wanted to see how this would come out using my fastest method that works first , next time I will cure longer and sit time overnight , still not sure which burnout cycle to try next , same one or the b9 green one ??
Mikkopee
Novice
Posts: 32
Joined: Mon Feb 13, 2017 1:18 pm

Re: ResinWorks EasyCastHD castable resin

Postby Mikkopee » Thu Mar 07, 2019 2:49 pm

Prints nice, tomorrow first cast. Hope casts well.
rkundla
Solus Expert
Posts: 276
Joined: Sat Jan 09, 2016 6:01 am

Re: ResinWorks EasyCastHD castable resin

Postby rkundla » Thu Mar 07, 2019 10:40 pm

rsaldivar wrote:that was my fist time growing and casting it , I did a 45 min. boil in water anniel , a 10 min. uv cure , 2 hours sit time with optima and a straight ramp to 1500 f for a total time in the oven of 6 hours , down to cast temp and this is my results , will try different thing next time , I wanted to see how this would come out using my fastest method that works first , next time I will cure longer and sit time overnight , still not sure which burnout cycle to try next , same one or the b9 green one ??


While it was kind of hard to tell from the photos, how did the non-drilled ring turn out versus the drilled ring? I saw that some of the holes were filled with gold requiring you to spend some time cleaning them up.
rsaldivar
Solus Expert
Posts: 282
Joined: Tue Jun 30, 2015 8:51 pm

Re: ResinWorks EasyCastHD castable resin

Postby rsaldivar » Fri Mar 08, 2019 9:43 pm

its as you said , some holes filled , so had to redrill them out , outside of that , every other spot came out perfectly , those filled holes I believe are what happens to letters when you try and cast fonts , in this case just redrill but if they would be fonts , then maybe have to recast and do extreme cure , annel , and react-sun dip ....
rsaldivar
Solus Expert
Posts: 282
Joined: Tue Jun 30, 2015 8:51 pm

Re: ResinWorks EasyCastHD castable resin

Postby rsaldivar » Fri Mar 08, 2019 9:52 pm

finished
Attachments
IMG_6492.jpg
printcast
Solus Expert
Posts: 156
Joined: Fri Oct 09, 2015 2:38 pm

Re: ResinWorks EasyCastHD castable resin

Postby printcast » Mon Mar 11, 2019 1:15 am

Good job!
rkundla
Solus Expert
Posts: 276
Joined: Sat Jan 09, 2016 6:01 am

Re: ResinWorks EasyCastHD castable resin

Postby rkundla » Thu Mar 14, 2019 1:22 am

Very nice - and sparkly! :D
lklutts
Solus Expert
Posts: 123
Joined: Thu Jul 16, 2015 8:48 pm

Re: ResinWorks EasyCastHD castable resin

Postby lklutts » Thu Mar 28, 2019 1:51 pm

I like r this resin. I don't over support. I add 3 supports at the bottom on each side of the ring support. I also am doing them manually.
Attachments
15537809275026122767909747793849.jpg
15537808912215008719382921034091.jpg
lklutts
Solus Expert
Posts: 123
Joined: Thu Jul 16, 2015 8:48 pm

Re: ResinWorks EasyCastHD castable resin

Postby lklutts » Thu Mar 28, 2019 1:54 pm

These supports are what I was talking about. It makes the difference. If you have trouble with it stopping printing above the base and shank I think this is the problem
Attachments
15537811220331550378647834232735.jpg
User avatar
sabushka
Novice
Posts: 11
Joined: Fri May 20, 2016 3:26 am
Location: Perth, Australia
Contact:

Re: ResinWorks EasyCastHD castable resin

Postby sabushka » Mon Apr 01, 2019 4:49 am

Hi
Any idea where I can get this Resin from. I am in Australia.
Thanks
Matrix 9, Solus, Jeweller, Setter, Engraver and always GRUMPY

Who is online

Users browsing this forum: No registered users and 3 guests