Easycast is a good resin. Almost identical to Emerald. Maybe, maybe slightly sharper. Maybe because of the slightly less exposure time which makes it also a bit faster which is a plus.
I would switch just to support the Solus team.
ResinWorks EasyCastHD castable resin
Re: ResinWorks EasyCastHD castable resin
How is the castabilty? The prints look nice and crisp.
Re: ResinWorks EasyCastHD castable resin
Kokos wrote:How is the castabilty? The prints look nice and crisp.
The same as the Emerald. I will make another thread comparing the 2 when i find time.
Re: ResinWorks EasyCastHD castable resin
I have a big question:
burnout chedule have a 2C per minunte. All ramp have 2 C per minute for option 2... but if you calculate will not reach the temperatures??
can anyone make clear ?
is 2C per minute for option 1 burnout or for both burnout options?
Thank you
burnout chedule have a 2C per minunte. All ramp have 2 C per minute for option 2... but if you calculate will not reach the temperatures??
can anyone make clear ?
is 2C per minute for option 1 burnout or for both burnout options?
Thank you
Re: ResinWorks EasyCastHD castable resin
How sticky is this resin compared to B9's Emerald?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: ResinWorks EasyCastHD castable resin
Not sticky at all. It's a really good resin. I suggest printing at 42xy build area with it for best results. Haven't had a single bad print or bad casting. It's miles better than the emerald and easier to post cure. Just cure in water for 30min - 1 hour under UV. Or for better results in glycerin or water/glycerin mix. Turns into hard plastic when completely cured.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: ResinWorks EasyCastHD castable resin
mongerdesigns wrote:Not sticky at all. It's a really good resin. I suggest printing at 42xy build area with it for best results. Haven't had a single bad print or bad casting. It's miles better than the emerald and easier to post cure. Just cure in water for 30min - 1 hour under UV. Or for better results in glycerin or water/glycerin mix. Turns into hard plastic when completely cured.
With what investment and burncycle?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: ResinWorks EasyCastHD castable resin
That info was mentioned in this thread.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: ResinWorks EasyCastHD castable resin
mongerdesigns wrote:Not sticky at all. It's a really good resin. I suggest printing at 42xy build area with it for best results. Haven't had a single bad print or bad casting. It's miles better than the emerald and easier to post cure. Just cure in water for 30min - 1 hour under UV. Or for better results in glycerin or water/glycerin mix. Turns into hard plastic when completely cured.
That's perfect! I'm starting to run low on my Emerald resin so I'll order an Easycast bottle next time. Thanks Emil.
Re: ResinWorks EasyCastHD castable resin
does the brow have wax in it ?
Who is online
Users browsing this forum: No registered users and 1 guest