I received an email from Junction 3D talking about the new SolusWax Pro resin as an improvement over the previous SolusWax, but haven't seen anything on this forum talking about it.
I am sure we are all 'burnt out' (pun intended) whenever a new castable resin comes along, but does anyone have anything to share about the resin? Experiences while printing, curing or casting? Photos showing off the detail of the prints? Pros or cons against the other castable resins mentioned on this forum?
So what is up with SolusWax Pro?
Re: So what is up with SolusWax Pro?
I wont be doing that again, lol. Resinworks works on my Solus.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: So what is up with SolusWax Pro?
Your choice.printcast wrote:I wont be doing that again, lol. Resinworks works on my Solus.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: So what is up with SolusWax Pro?
Ordered the SolusWax Pro resin today.
Early Christmas present for my Solus printer.
Early Christmas present for my Solus printer.
Re: So what is up with SolusWax Pro?
is this replacing the normal soluswax resin or will both be available?
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: So what is up with SolusWax Pro?
No more regular SolusWax.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: So what is up with SolusWax Pro?
Any casting pics from fellow users? (Not casting houses)
Can it handle 0.2mm sphere supports?
How does it compare in terms of printing reliability compared to the Emerald or the Proto?
Does it need to be heated?
Thank you.
Can it handle 0.2mm sphere supports?
How does it compare in terms of printing reliability compared to the Emerald or the Proto?
Does it need to be heated?
Thank you.
Re: So what is up with SolusWax Pro?
Jeweltool did you get your bottle yet? I ordered a sample bottle also, hopefully I will get mine before next weekend. Crazy how expensive the stuff is. The pictures of the prints and castings look great! I've only used emerald b9c in the past but the soluswax looks to have just as crisp detail but with a smoother surface. I hope its easier to cast. Does anyone know if this resin can be used to make molds? heated to 307 F? or will it melt? Is there a large ratio of wax in this stuff?
Re: So what is up with SolusWax Pro?
Very good castings with SolusWax Pro.
I have tried a lot of resins over the years.
Much better than my go to B9 Cherry..
I have tried a lot of resins over the years.
Much better than my go to B9 Cherry..
Re: So what is up with SolusWax Pro?
That's good to hear. Just received my bottle today. I hope to get a chance next week to test it.
Did you follow their recommended fast burnout?
Did you follow their recommended fast burnout?
Who is online
Users browsing this forum: No registered users and 12 guests