I would like to mention once more that the yellow resin casts great. Curing is primordial to any successful casting.
I have seen people struggling with white gold casting.Though one major thing they always neglect is they must have 1/2 ratio of fresh white gold.
Hybrid Resin Blend (WaxCast and Emerald)
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: Hybrid Resin Blend (WaxCast and Emerald)
Good job on the print and cast, Bob. Thank you for sharing.
By the way, Emil. I was about to ask you about that flashing around the base like the last pic that Bob posted. I got the Dynamic Range problem resolved on my laptop by installing the third party toggling software in the link that you and Mark sent me. However, I still got that flashing around the base. and it happens to me even with the b9 Emerald by itself. I think it is because of the 3500 Lumen that my Vivitek HD913 has instead of 2000 Lumen. Right now my bottom exposure is 16000. How much do you think I should lower it? Thank you.
By the way, Emil. I was about to ask you about that flashing around the base like the last pic that Bob posted. I got the Dynamic Range problem resolved on my laptop by installing the third party toggling software in the link that you and Mark sent me. However, I still got that flashing around the base. and it happens to me even with the b9 Emerald by itself. I think it is because of the 3500 Lumen that my Vivitek HD913 has instead of 2000 Lumen. Right now my bottom exposure is 16000. How much do you think I should lower it? Thank you.
mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Re: Hybrid Resin Blend (WaxCast and Emerald)
mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Will do! Thanks for the tip!!
B
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Hybrid Resin Blend (WaxCast and Emerald)
samatheang wrote:Good job on the print and cast, Bob. Thank you for sharing.
By the way, Emil. I was about to ask you about that flashing around the base like the last pic that Bob posted. I got the Dynamic Range problem resolved on my laptop by installing the third party toggling software in the link that you and Mark sent me. However, I still got that flashing around the base. and it happens to me even with the b9 Emerald by itself. I think it is because of the 3500 Lumen that my Vivitek HD913 has instead of 2000 Lumen. Right now my bottom exposure is 16000. How much do you think I should lower it? Thank you.mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Keep lowering it until the flashing goes away.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: Hybrid Resin Blend (WaxCast and Emerald)
Ok, thanks! I will try it.
-
- Novice
- Posts:96
- Joined:Mon Mar 28, 2016 8:05 am
Re: Hybrid Resin Blend (WaxCast and Emerald)
Thanks for sharing Bob!
Did you make a 50:50 mix with the emerald and the MJ wax cast ? And how did you cure the prints? Microwave and UV?
Did you make a 50:50 mix with the emerald and the MJ wax cast ? And how did you cure the prints? Microwave and UV?
Re: Hybrid Resin Blend (WaxCast and Emerald)
is waxcast better than emerald or yellow alone? if not, why use waxcast?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Green and mj lighter color is cured
Re: Hybrid Resin Blend (WaxCast and Emerald)
I have found the combo of green and makerjuice to be very strong. It doesn't appear to need as many supports. The bamboo band is over 16mm wide and I have 1 row of supports in the center
Re: Hybrid Resin Blend (WaxCast and Emerald)
Would the same method apply for cherry 50:50? With adjusted base and layer exposure?
Who is online
Users browsing this forum: No registered users and 108 guests