Page 2 of 6
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 06, 2016 12:28 am
by M-Williams
I would like to mention once more that the yellow resin casts great. Curing is primordial to any successful casting.
I have seen people struggling with white gold casting.Though one major thing they always neglect is they must have 1/2 ratio of fresh white gold.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 06, 2016 1:05 am
by samatheang
Good job on the print and cast, Bob. Thank you for sharing.
By the way, Emil. I was about to ask you about that flashing around the base like the last pic that Bob posted. I got the Dynamic Range problem resolved on my laptop by installing the third party toggling software in the link that you and Mark sent me. However, I still got that flashing around the base. and it happens to me even with the b9 Emerald by itself. I think it is because of the 3500 Lumen that my Vivitek HD913 has instead of 2000 Lumen. Right now my bottom exposure is 16000. How much do you think I should lower it? Thank you.
mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 06, 2016 1:49 am
by Just Bob
mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Will do! Thanks for the tip!!
B
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 06, 2016 2:12 am
by mongerdesigns
samatheang wrote:Good job on the print and cast, Bob. Thank you for sharing.
By the way, Emil. I was about to ask you about that flashing around the base like the last pic that Bob posted. I got the Dynamic Range problem resolved on my laptop by installing the third party toggling software in the link that you and Mark sent me. However, I still got that flashing around the base. and it happens to me even with the b9 Emerald by itself. I think it is because of the 3500 Lumen that my Vivitek HD913 has instead of 2000 Lumen. Right now my bottom exposure is 16000. How much do you think I should lower it? Thank you.
mongerdesigns wrote:Nice. Lots more photos
Bob, I see some flashing around the bases on the last photo. Try lowering your bottom layer exposure a bit and it should get rid of that flashing.
Keep lowering it until the flashing goes away.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 06, 2016 7:00 am
by samatheang
Ok, thanks! I will try it.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Sat May 07, 2016 5:15 am
by studiojoia
Thanks for sharing Bob!
Did you make a 50:50 mix with the emerald and the MJ wax cast ? And how did you cure the prints? Microwave and UV?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Thu May 19, 2016 5:47 pm
by Wdshea
is waxcast better than emerald or yellow alone? if not, why use waxcast?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 20, 2016 9:20 pm
by lklutts
Green and mj lighter color is cured
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 20, 2016 9:25 pm
by lklutts
I have found the combo of green and makerjuice to be very strong. It doesn't appear to need as many supports. The bamboo band is over 16mm wide and I have 1 row of supports in the center
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Tue May 24, 2016 4:11 pm
by Joetrfj
Would the same method apply for cherry 50:50? With adjusted base and layer exposure?