Page 3 of 6
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Tue May 24, 2016 7:08 pm
by mongerdesigns
Joetrfj wrote:Would the same method apply for cherry 50:50? With adjusted base and layer exposure?
Cherry and red 50:50 is not capable of supporting the high resolutions we are outputting. Use cherry by itself.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Wed May 25, 2016 8:20 am
by Joetrfj
mongerdesigns wrote:Joetrfj wrote:Would the same method apply for cherry 50:50? With adjusted base and layer exposure?
Cherry and red 50:50 is not capable of supporting the high resolutions we are outputting. Use cherry by itself.
Sorry, I meant wax cast and cherry 50:50?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Wed May 25, 2016 4:05 pm
by jdwages
Emil I have been having some flashing also. Any idea on what setting should be lowered to. I am using the profile for B9 emerald. Thanks
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Wed May 25, 2016 5:39 pm
by mongerdesigns
jdwages wrote:Emil I have been having some flashing also. Any idea on what setting should be lowered to. I am using the profile for B9 emerald. Thanks
Check that the RGB setting is still on full. If it is, lower the bottom exposure a bit, until you have no flashing. If you have some photos of the flashing, email them to me.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Wed May 25, 2016 7:07 pm
by Joetrfj
Joetrfj wrote:mongerdesigns wrote:Joetrfj wrote:Would the same method apply for cherry 50:50? With adjusted base and layer exposure?
Cherry and red 50:50 is not capable of supporting the high resolutions we are outputting. Use cherry by itself.
Sorry, I meant wax cast and cherry 50:50?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Thu May 26, 2016 3:29 am
by reify
Joetrfj wrote:Joetrfj wrote:mongerdesigns wrote:
Cherry and red 50:50 is not capable of supporting the high resolutions we are outputting. Use cherry by itself.
Sorry, I meant wax cast and cherry 50:50?
If anybody has some extra cherry would they mind mixing it with some waxcast to see how it prints.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Fri May 27, 2016 6:55 pm
by samatheang
Could anyone share the burning schedule for the hybrid please? Also, how long does it take to cure the Hybrid? Thank you.
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Sat May 28, 2016 2:50 am
by lklutts
Not saying I have it down, but getting a grasp on it. I use the green settings for growing. I will post later my machine it's running. I have been curing in uv lamp for an hour or so.Then into my lizard lamp I got from pet mountain. 100 watt, heat,uv and ir. At the height of the box, high tech me, it goes to 150-160. I leave it till it looks cured some an hour, some three. Turn it a couple times to keep it even.
300 1.5 hours
800-2 hours
1350 3 hours
Back to soak temp
vacuum and cast
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Sat May 28, 2016 4:16 am
by KBS756
Has anyone tried printing say 25:75 Emerald : WaxCast or even 10:90 Emerald:Waxcast to see if one can get away with support and such issues while still retaining the wax characteristics of Wax cast?
I'm going to try it this weekend .. what settings would be a good starting point for hybridizing to this degree?
Re: Hybrid Resin Blend (WaxCast and Emerald)
Posted: Sat May 28, 2016 11:07 am
by Joetrfj
Is 50:50 or 60:40 green and WC the most stable?