Fail ring print with B9 Emerald
- Jewelermdt
- Solus Master
- Posts:809
- Joined:Sun Jul 19, 2015 10:38 pm
- Location:N.W. Florida
- Contact:
Might need to double check your display settings. the flashing I believe is because something is not set right.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Fail ring print with B9 Emerald
Yes. Looks like the full rgb issue. Make sure to follow the setup instructions step be step.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: Fail ring print with B9 Emerald
I have the same issues with Emerald by itself. Used all suggested settings but 9/10 always had failed prints with massive amounts of flashing, never got to the bottom of why it did it. Mix a little MJ wax cast into the emerald thoroughly, it solved the problem for me.
Joe
Joe
Re: Fail ring print with B9 Emerald
Hmmm....... What projector are you using and is the uv filter removed?
-
- Novice
- Posts:27
- Joined:Mon Apr 25, 2016 10:29 pm
Re: Fail ring print with B9 Emerald
I'm using the Optoma HD37 1080p 3D DLP Home Theater Projector. Yes I remove the filter. I did print a couple of things but more failures than success.
I rechecked the projector settings and they were not correct. I made the corrections now printing. I'll provide status one cycle is complete.
My print is still failing.
I rechecked the projector settings and they were not correct. I made the corrections now printing. I'll provide status one cycle is complete.
My print is still failing.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Fail ring print with B9 Emerald
You had the wrong settings and it failed? Now you have the right settings and it failed again? Maybe you can post a photo? Still getting flashing around the bases?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:27
- Joined:Mon Apr 25, 2016 10:29 pm
-
- Novice
- Posts:27
- Joined:Mon Apr 25, 2016 10:29 pm
Re: Fail ring print with B9 Emerald
In tools and tips the following note was posted. I don't see how to check these settings.
For the Optoma HD37, we recommend the following settings.
DISPLAY MODE: Reference
Brightness: 0
Contrast: 15
Sharpness: 15
Gamma: 1.8
Lamp Mode: ECO
High Altitude: On
Note: The Power Mode should remain unchanged on Active, not Eco. This is not the same as the Lamp Mode.
For the Optoma HD37, we recommend the following settings.
DISPLAY MODE: Reference
Brightness: 0
Contrast: 15
Sharpness: 15
Gamma: 1.8
Lamp Mode: ECO
High Altitude: On
Note: The Power Mode should remain unchanged on Active, not Eco. This is not the same as the Lamp Mode.
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: Fail ring print with B9 Emerald
You use the remote control for the projector to set those settings on the projector menu. Kinda important.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Novice
- Posts:27
- Joined:Mon Apr 25, 2016 10:29 pm
Re: Fail ring print with B9 Emerald
I went back and checked all my setting. Misted one setting in the projector. The print was better but still failed. I added some MJ cast to the emerald green and it worked.
Who is online
Users browsing this forum: No registered users and 165 guests