solus wax burnout
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
We have been using Plasticast for a while now and I assume it is the casting investment of choice when it comes to resin. Smooth, very strong and Extremely forgiving material when it comes to temperature ramp ups. Marc.
Re: solus wax burnout
Thanks Marc
I have to try plasticast
Regards
I have to try plasticast
Regards
Re: solus wax burnout
Juar75 wrote:1. The ramping straight from 80F to 1450F in 1.5hrs was too fast??
for a flask of 2.5 in x 2.5 in, (just one ladies ring) that was sitting for 1.5 hrs after investing with ultravest maxx 38:100
What is a good time for reach the 1450F?
I run Prestige Optima at 1000°F/hour ramp time up to 1450°F and haven't seen a problem. How old is your investment? Maybe the component ratios are messed up if it isn't mixed well? If you give it a little more dry time before putting it in the kiln, it might give it more strength against the rapid removal of water vapor within the flask.
Juar75 wrote:2. Or my kiln it's not enough calibrate and maybe is more than 1450F?
That could be a problem if you aren't 100% sure where your kiln falls temperature wise. You could get some pyrometric cones to do a test if you don't have another high-temp thermocouple available to measure against. https://digitalfire.com/glossary/cones
Re: solus wax burnout
Thank you for answer,
My investment is fresh it have like 4 months since it was made,
I'll try to do more dry time , for test it also try a slower ramp speed.
Also it's a great idea to try the pyrometric cones to be sure my kiln temp.
Thanks a lot!!
My investment is fresh it have like 4 months since it was made,
I'll try to do more dry time , for test it also try a slower ramp speed.
Also it's a great idea to try the pyrometric cones to be sure my kiln temp.
Thanks a lot!!
Re: solus wax burnout
Juar75 wrote:
I just do it today and the top of my flask was broken, with soluswax pro
so i have some doubts:
1. The ramping straight from 80F to 1450F in 1.5hrs was too fast??
2. Or my kiln it's not enough calibrate and maybe is more than 1450F?
Regards
I have been casting the Solus Wax Pro for a couple of months now with no issues. Loving it. I am using Omega + as I did with all the B9 resins.
I put the flask in the kiln and ramp up to 1450 in an hour to 1hr 20min. I use an old Neycraft and I just have a number I set it to that I know will achieve the ramp. The more I have in the kiln the longer it takes. About 2/3rds the way through my ramp to 1450 I flip my flasks. Just about when everything is burning.
I sit my investment for 90 min after pour and then cast straight away. Only issues I have had was when my slurry was too cold...so not the fault of the resin. Great product for me.
cheers,
Sochin
Re: solus wax burnout
Thanks Sochin
For your answer,
what size are your flasks?
For your answer,
what size are your flasks?
Re: solus wax burnout
Juar75 wrote:what size are your flasks?
2 1/4 inch diameter. I had some taller ones made that are about 4 inches tall but the others are about as tall as they are in diameter.
Might be one of the reasons I have success as I usually cast small flasks. I am usually casting 3- 5 flasks that size at a time. Good luck.
cheers,
Sochin
Re: solus wax burnout
Juar75 ,
I do 2.5 flasks , I also do straight to 1500 , I also investing with ultravest maxx 38:100 , but I leave it overnight to dry , you are doing nothing wrong , just let it sit for 3 - 5 hours at a min. , I know what the books say , just try this , see my casting post
I do 2.5 flasks , I also do straight to 1500 , I also investing with ultravest maxx 38:100 , but I leave it overnight to dry , you are doing nothing wrong , just let it sit for 3 - 5 hours at a min. , I know what the books say , just try this , see my casting post
Re: solus wax burnout
Thank you for your help,
yes, the last castings I left more time to dry and the castings were very good,
but since I don't want to fail again, I also mix the water with boric acid 2%, and give a slower ramp in the oven,
my flask are 2.5 x 2.5 in, and the total time in oven is around 7.5 hours
I'll try the straight ramp in the oven with your tip ( overnight to dry)
Regards
yes, the last castings I left more time to dry and the castings were very good,
but since I don't want to fail again, I also mix the water with boric acid 2%, and give a slower ramp in the oven,
my flask are 2.5 x 2.5 in, and the total time in oven is around 7.5 hours
I'll try the straight ramp in the oven with your tip ( overnight to dry)
Regards
Re: solus wax burnout
I use boric also , but when Im doing wax only now , the boric cleans the wax and casting come out cleaner and smoother , however I don't use it anymore with the resins because I want my investment stronger, the boric weakens the composition of the investment , I recommend don't use it and do the 3-5 hour sit time or overnight if poss. , then from room Temp straight up to 1450 and leave it there for 4 hours , then drop to cast Temp. and cast ,
Also,
1. grown the resin ,
2. wash in Alcohol and then tree up and invest ,
3. NO UV cure if your using the soluswax Pro
Also,
1. grown the resin ,
2. wash in Alcohol and then tree up and invest ,
3. NO UV cure if your using the soluswax Pro
Who is online
Users browsing this forum: No registered users and 3 guests