auto support on mirco prongs heavy ring
Emil , would you recommend including the sprues to be grow in the file with this resin ??
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: auto support on mirco prongs heavy ring
Sure, you can do that. But might take longer to grow depending on the position of your sprue.
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: auto support on mirco prongs heavy ring
also , will contour ever have an option for not raising or limiting the heith of the tallness of the grow, I mean being able to control the height of the model being raised and adding more time to the grow , or is that height been shown to have the most success rate as a result ??
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: auto support on mirco prongs heavy ring
dcpattni wrote:@ mongerdesigns,
Request can you plz try with new resin (SOLUS blue resin) ring which I posted......also share supports sizes etc.
Don't have much time but it was interesting to see how it would pull it off. No sweat. The support tips are the smallest at 0.1 and automatic supports were used.
Hope you don't mind if I take this print to the JCK
https://instagram.com/p/BUnuJ8lDMSN/
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
-
- Solus Expert
- Posts:197
- Joined:Wed Feb 17, 2016 10:36 pm
Re: auto support on mirco prongs heavy ring
That's sooo coool!
Re: auto support on mirco prongs heavy ring
Now perfect casting and you have a winner!!
Can't wait to have the blue stuff...
Can't wait to have the blue stuff...
Re: auto support on mirco prongs heavy ring
@ mongerdesigns
Print is wow wow wow.....and autosupport @0,1mm is also wow!!!!!
i don't mind atall.....thank you very much for trail print.
I love my Solus printer!!!.
Print is wow wow wow.....and autosupport @0,1mm is also wow!!!!!
i don't mind atall.....thank you very much for trail print.
I love my Solus printer!!!.
- M-Williams
- Solus Master
- Posts:393
- Joined:Sun Nov 01, 2015 4:45 pm
Re: auto support on mirco prongs heavy ring
You can't go wrong with countour. you need just to pay attention to any overhang .
Re: auto support on mirco prongs heavy ring
hi,
after suggestion from SOlUS users experts i try as below:-
1st try single ring white 0.1mm support which print good easy to removed supports but bottom(dome area) prongs it was not perfect.
2nd try in 2 parts as Mr.Sam advice, it worked very clear but top front only it did not print well....but rest was clean & clear images below.
3rd try with 0.2mm only for Dome it didn't grow....
All suports are manualy.
I always mix b9 very very well before filling in VAT.
what do you think........i m doing few other printing going OK....only this ring mirco prongs giving tuff time.
after suggestion from SOlUS users experts i try as below:-
1st try single ring white 0.1mm support which print good easy to removed supports but bottom(dome area) prongs it was not perfect.
2nd try in 2 parts as Mr.Sam advice, it worked very clear but top front only it did not print well....but rest was clean & clear images below.
3rd try with 0.2mm only for Dome it didn't grow....
All suports are manualy.
I always mix b9 very very well before filling in VAT.
what do you think........i m doing few other printing going OK....only this ring mirco prongs giving tuff time.
Re: auto support on mirco prongs heavy ring
clearly seen dome area prongs are not good.
Who is online
Users browsing this forum: No registered users and 2 guests