I cut off the hard to reach support of 0.5mm drills .... Side edge ...
I do it under the microscope and can be very precise to cut off the support
SolusCast: Cracks in heavy model
Re: SolusCast: Cracks in heavy model
hello everyone,
sorry for delay near my house area we have power problems..
Result very very bad. Investement in cool water 40/100 SRS cadcast without boric powder....
bench sit 48hours
165C-3h
550C-2h
780C-7h
casting temp 620-630c which i always do on silver and gold....
SILNOVA-02 Silver was used it gives smooth casting but this time it not good.
sorry for delay near my house area we have power problems..
Result very very bad. Investement in cool water 40/100 SRS cadcast without boric powder....
bench sit 48hours
165C-3h
550C-2h
780C-7h
casting temp 620-630c which i always do on silver and gold....
SILNOVA-02 Silver was used it gives smooth casting but this time it not good.
Re: SolusCast: Cracks in heavy model
round, oval and cushion casting investment mixed with 2% boric powder....
all castable resin i must flip flask up & down for vaccum then return back in oven for 2-3hours @ 780c
b9 resin no problem while casting.....i have another 3rd door in SC resin what do you advice next...
i really like to see my casting like others doing with SC resin....
all castable resin i must flip flask up & down for vaccum then return back in oven for 2-3hours @ 780c
b9 resin no problem while casting.....i have another 3rd door in SC resin what do you advice next...
i really like to see my casting like others doing with SC resin....
- mongerdesigns
- Solus Guru
- Posts:1950
- Joined:Sat Apr 25, 2015 5:16 pm
- Location:Los Angeles
- Contact:
Re: SolusCast: Cracks in heavy model
How do you post cure your SC prints?
Monger Designs a.k.a. Monger
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
http://www.mongerdesigns.com
Junction3d - Official US Distributor for the SOLUS 3D PRINTER
http://www.junction3d.com
Follow us on Instagram!
https://www.instagram.com/junction3d/
Re: SolusCast: Cracks in heavy model
send me the file
Re: SolusCast: Cracks in heavy model
dcpattni
That window looking design has a lot of wax sprues. How do those wax sprues look in that cast? Are they smooth and clean or are they flawed too. If they are flawed like the SC cast then you have an issue apart from SC.
That window looking design has a lot of wax sprues. How do those wax sprues look in that cast? Are they smooth and clean or are they flawed too. If they are flawed like the SC cast then you have an issue apart from SC.
Re: SolusCast: Cracks in heavy model
Hello,
@printcast they are clean smooth...
@rsaldivar give me your email i'll fwd.
@printcast they are clean smooth...
@rsaldivar give me your email i'll fwd.
printcast wrote:dcpattni
That window looking design has a lot of wax sprues. How do those wax sprues look in that cast? Are they smooth and clean or are they flawed too. If they are flawed like the SC cast then you have an issue apart from SC.
Re: SolusCast: Cracks in heavy model
sent , ck your pm
Re: SolusCast: Cracks in heavy model
Hello,
I also have this type of problems "craking" but in the resin model, since I got the new version of contour,
Is there a way to go back to the older version?
Thank you guys!
I also have this type of problems "craking" but in the resin model, since I got the new version of contour,
Is there a way to go back to the older version?
Thank you guys!
Who is online
Users browsing this forum: No registered users and 22 guests